The free convection heat transfer coefficient on a thinhot vertical plate suspended in still air can be determined from observations of the change in plate temperature withtime as it cools. Assuming the plate isisothermal and radiation exchange with its surroundings is negligible, evaluate the convection coefficient atthe instant of time when the plate temperature is 225°Cand the change in plate temperature with time
Trending nowThis is a popular solution!
Chapter 1 Solutions
Fundamentals of Heat and Mass Transfer
- The heat transfer rate from hot air by convection at 100C flowing over one side of a flat plate with dimensions 0.1m0.5m is determined to be 125 W when the surface of the plate is kept at 30C. What is the average convection heat transfer coefficient between the plate and the air?arrow_forwardThe air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specifiedarrow_forwardAn electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.arrow_forward
- Determine the rate of heat transfer per meter length from a 5-cm-OD pipe at 150C placed eccentrically within a larger cylinder of 85 magnesia wool as shown in the sketch. The outside diameter of the larger cylinder is 15 cm and the surface temperature is 50C.arrow_forwardA horizontal, 3-mm-thick flat-copper plate, 1-m long and 0.5-m wide, is exposed in air at 27C to radiation from the sun. If the total rate of solar radiation absorbed is 300 W and the combined radiation and convection heat transfer coefficients on the upper and lower surfaces are 20 and 15W/m2K, respectively, determine the equilibrium temperature of the plate.arrow_forward1.21 In an experimental set up in a laboratory, a long cylinder with a 5-cm diameter, and an electrical resistance heater inside its entire length is cooled with water flowing crosswise over the cylinder at and a velocity of 0.8 m/s. For these flow conditions, 20 kW/m of power is required to maintain a uniform temperature of at the surface of the cylinder. When water is not available, air at is used with a velocity of 10 m/s to maintain the same surface temperature. However, in this case, the cylinder surface heat dissipation rate is reduced to 400 W/m. Calculate the convection heat transfer coefficients for both water and air, and comment on the reason for the differences in the values.arrow_forward
- When a flat plate is subjected to uniform heat flux, how different are the relations compared to the isothermal plate case? Questions above are related to Heat transferarrow_forwardA food product with 80% moisture content in a 5 cm diameter can wants to be frozen. The density of the product is 1000 kg / m cubic, the thermal conductivity is 1.0 W / (m K), and the initial freezing temperature is -1.75 ° C. After 10 hours in -25 ° C freezing medium, the product temperature becomes -10 ° C. Estimate the convection heat transfer coefficient of the freezing medium. Assume the can as an infinite cylinderarrow_forwardA food product wants to be produced in a small round shape (pellet) by freezing it in a water blast freezer freezer. Air freezer operates at a temperature of -35 ° C. The initial product temperature is 25 ° C. The pellet has a diameter of 1 cm, and a density of 980 kg / m³. The initial freezing temperature is -2.5 ° C. The latent heat of freezing of the product is 280 kJ / kg. The thermal conductivity of the frozen product is 1.9 W / (m ° C). The convective heat transfer coefficient is 50 W / (m² K). Calculate the freeze time. t f = hourarrow_forward
- A 5.0 -cm-diameter aluminum cylinder is maintained at a temperature of 50-C in a large room where the air and wall temperature are at 20-C. The surface emissivity of the aluminum may be taken as 0.8 and the heat-transfer coefficient equal 6.5 W/m. C, calcualate the total heat lost by the pipe per unit length. (Stefan - Boitzmann constant = 5.669 x 10)arrow_forwardDefine the cooling of a boiled egg by forced and natural convection.arrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning