Q4. Draw the logic diagram of a four-bit register with four D flip-flops and four 4x1 multiplexers with mode selection inputs S1 and S0. The register operates according to the following function table. S1 so Register Operation No Shift 1 1's complement and right shift 1 Clear register to 0 1 1 Load parallel data

Q4. Draw the logic diagram of a four-bit register with four D flip-flops and four 4x1 multiplexers with mode selection inputs S1 and S0. The register operates according to the following function table. S1 so Register Operation No Shift 1 1's complement and right shift 1 Clear register to 0 1 1 Load parallel data

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

The 3-bit shift register is shifted five times to the right with the serial input being 1011101. What is the content of the register? (Write your answer using only 0s and/or 1s.)
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
14.) Using rising edge JK-Flipflops and Digital Logic Gates, build a 4-Stage Shift Register. I recommend labeling D0, Q0, Q1, etc. Based on the waveforms for the CLK (clock) and D0 input generate the waveforms for Q0, Q1, Q2, Q3. DO CLK QO Q1 Q2 Q3
1. Assume that the registers are 8-bit wide. Consider the following code: MOV R1, #4A MOV R2, #40 ADD R3, R1, R2 a) What will be the 8-bit result in Register R3 (in hex)? b) What is the 8-bit result in Register R3 (as unsigned decimal)? c) What is the 8-bit result in Register R3 (as signed decimal)? d) What will be the value of the carry (C) bit?
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
show how to design a 8-bit Function Unit Combining Arithmetic Logic Unit (ALU) and a Shifter that can perform the operations given in table 1 below. Use X and Y as 8 bits input and F as 8 bits output as shown in Figure 1. S0,S1,S2 and S3 represent the selction code in the operation set table Three statue bits V (over flow), C (carry), N (negative) and are related to arrithmatic operations and statue bit Z (zero) is relataed to both arrithmatic and logic operation. Test your designed Function Unit with necessary tables.
Write a program to PUSH R0, R1, and R3 of Bank 0 onto the stack and POP them back into R5, R6, and R7 of Bank 3. Also, mention the value of SP register after every PUSH and POP operation. this question is asked in microprocessor and microcontroller
What is the function of the odd parity generator circuit? O a. produces an output of 'I' for even number of logic T O b. produces an output of '0' for odd number of logic T' O c. produces an output of '1' for odd number of logic T shift? What is the difference between a left logical shift and a left arithmet O a. logical shift feeds a '0' in the MSB O b. arithmetic shift feeds a '0' in the MSB O c. no difference
Design a parallel-input parallel-output (PIPO) 3-bit Register using D-flipflops. The register has twoinput lines for operation selection. Based on the values of the input lines, the register can perform thefollowing four operations00 – Shift Right01 – Shift Left10 – Decrement (-1)11 – Increment (+2)
This question is from the subject Digital Logic Design. Assume your register number SF20-BEC-xxx (excluding the dashes -) is in Hexadecimal, where xxx are the three digits of your registration number. a) Represent your registration number in the binary.b) Split the ten digits of your registration into two Hexadecimal numbers M and N, where the left most five digits make number M and the right most five digits make number N. Using r’s complement, subtract N from M. In other words, calculate M – N. Solve the question for registration no SF20-BEC-156.
Electrical Engineering Draw 2, 1 bit ALUS to create a basic 2 bit ALU. the carry out and carry in bits must ripple across. The ALU should subtract/add, logical NOR, logical AND, and logical OR. Draw out the adding logic circuit
Topic is about shift registers in electrical engineering. 1. What is the main functional purpose of a register? We are looking for the specifics of what a register does in isolation, not with respect to applications. 2. In what cases might we use serial and parallel inputs/outputs? 3. Describe the purpose of the debouncer in your own words. 4. Is an SN5474 the same as an SN 7474? If not, how do they differ?