1- A digital computer has a memory unit with 64 bits per word and 256G memory. The instruction set consists of 532 different operations. All instructions have an opcode, general register, index register, mode, future and address fields. This particular system includes 32 general- purpose registers, 8 index register,4 modes, future and address. a) How many bits are needed for the opcode? b) How many bits are needed to specify the general and index registers? c) How many bits are needed to specify the mode and the future?

1- A digital computer has a memory unit with 64 bits per word and 256G memory. The instruction set consists of 532 different operations. All instructions have an opcode, general register, index register, mode, future and address fields. This particular system includes 32 general- purpose registers, 8 index register,4 modes, future and address. a) How many bits are needed for the opcode? b) How many bits are needed to specify the general and index registers? c) How many bits are needed to specify the mode and the future?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it
Question 1: Use Indirect addressing to write a PIC24 assembly code that complements and adds 5 and multiply by 2 to 1024 data bytes into the memory at starting address Ox1000. The original data are stored in the memory starting from address 0x800. it is an electrical engineering question . this is the full information about the question!
This question is from the subject Digital Logic Design. Assume your register number SF20-BEC-xxx (excluding the dashes -) is in Hexadecimal, where xxx are the three digits of your registration number. a) Represent your registration number in the binary.b) Split the ten digits of your registration into two Hexadecimal numbers M and N, where the left most five digits make number M and the right most five digits make number N. Using r’s complement, subtract N from M. In other words, calculate M – N. Solve the question for registration no SF20-BEC-156.
1. Assume that the registers are 8-bit wide. Consider the following code: MOV R1, #4A MOV R2, #40 ADD R3, R1, R2 a) What will be the 8-bit result in Register R3 (in hex)? b) What is the 8-bit result in Register R3 (as unsigned decimal)? c) What is the 8-bit result in Register R3 (as signed decimal)? d) What will be the value of the carry (C) bit?
6) Write an 8086 assembly language program to multiply the contents of the registers CL & BL by using repeated addition and store the result in AX. 0006
write down the register types of the microprocessor the explain the function two register of each types 1:04 PM✓
Implement a byte-addressable instruction memory using Verilog (address locations are 8 bit) Information in Image
ehcu.org/pluginfile 100% 10 / 11 locations, count how many times is 0 and how many times 1 is. Questions:- 1- Write a program in assembly language to perform the following logic ci BL CL DL [5100]- 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX , FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX , LG
1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
Q1. Design a circuit of General register organization in which 4 registers are there from R0 to R3. (a) Explain the control word as per the register configuration given above.
Discussions: 1) Why are shift registers considered basic memory devices?
Discuss in detail about RAM allocation in 8051 and Analyse, and explain the objective of the following 8051 assembly language program. Specify the content of the Program Status Word (PSW) register after the execution of each instruction. ORG 00H MOV A#00H MOV R5,A MOV R0,#0FBH ADD A#0FEH JNC NI INC R5 N1: ADD A, #0F5H JNC N2 INC R5 N2: ADD A#0F2H INC OVER INC R5 OVER: MOV @R0, A END Comment every line of the program and specify the register contents on single-step execution.