Procedure: 1. Design an even/odd parity generator for 4-bit data. 2. Design a parity checker circuit for a 4-bit data. 3. Design a logic circuit for a 3-bit message to be transmitted with an even parity bit. 4. Four data bits are to be transmitted. Design a parity bit generator to give an o/p of 'l' if the number of logic l's in the message is: (i) odd; (ii) even.

Procedure: 1. Design an even/odd parity generator for 4-bit data. 2. Design a parity checker circuit for a 4-bit data. 3. Design a logic circuit for a 3-bit message to be transmitted with an even parity bit. 4. Four data bits are to be transmitted. Design a parity bit generator to give an o/p of 'l' if the number of logic l's in the message is: (i) odd; (ii) even.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

the diagram on the right is for a register bank circuit that contain 8 registers. Each register is 16-bit. Theregister can read or write to one register at a time using address bus.Design the circuit and specify the width of EVERY bus.
Draw a dataflow circuit using block components that lets you add or subtract two input numbers in all possible ways. Your circuit will have two inputs X, Y and one output Out. You’ll have an adder and you’ll need to use multiplexers on each input to the adder. Clearly specify the number and type of control bits needed.
H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef
DISCUSSION: 1- Is the Gray code arithmetic code? Why? Where this code usėd? 2- What is the parity bit? 13- Design five - bit odd parity checker? 4- a) What are the main applications of the comparator? /b) Design two – two bit comparator. -5- Convert five.bit Gray to binary code, write truth table and draw the circuit diagram. 2-5
dont use others answers show your work step by step short answer Suppose we are given the following subset of binary words, created for a 7-bit memory word with one parity bit: 11100110, 00001000, 10101011, and 11111110. Does this code use even or odd parity? Explain in 1-2 sentences.
USE DIGITAL LOGIC AND DESIGN Part 1: In Figure_4; we have 4-bit Comparator using 2-bit Comparators block. You have to satisfy given condition by applying all data on figure 4. At the end, given condition should produce HIGH output and other two should be LOW. A3 A2 A1 A0 = 1101 and B3 B2 B1 B0 = 1110 Figure_4 Part 2: The serial data-input waveform (Data in) and data-select inputs (S0 and S1) are shown in Figure_5. Determine the data-output waveforms from D0 through D3. Figure_5 Part 3: Decoder can be useful when we have to decode some specific numbers from their equivalent code. Figure 6 has a concept of 3 to 8 line decoder from which you have to generate output waveform from D0 to D7 with proper relationship to input. Figure_6 Part 4: The data-input and…
Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.
Suppose RO contains "Ox02145321" and R1 contains "Ox00200020", and the C bit of the APSR is set to 1. What is the value of R2 after the following line executes? (enter this value in decimal) ADD R2, R1, RO
24. a. The serial adder required six clock pulses to add two, three bit binary numbers. (True or False. Write the correct one, if it's false) b. A three bit parallel adder circuit uses three adders to add all bits on two clock pulse. (True or False. write the correct one, if it's false) c. What is the two's complement of 1001?
1) What is the biggest binary number (decimal value) you can write with 6 bits? What is the biggest binary number (decimal value and in terms of n) you can write with n bits? If you want to represent the decimal numbers from 0-16, what is the minimum number of bits you will need? Convert the decimal number 238 to binary number. (ZERO point if not showing steps/calculation!)
20. Suppose we have just found yet another representation for floating point numbers. Using this representation, a li2-bit floating point number has 1 bit for the sign of the number, 4 bits for the exponent and 7 bits for the mantissa, which is normalized as in the Simple Model so that the first digit to the right of the radix points must be a 1. Numbers in the exponent are in signed 2's complement representation. No bias is used and there are no implied bits. Show the representation for the smallest positive number this machine can represent using the following format (simply fill in the squares provided). What decimal number does this equate to? : SIGN EXPONENT MANTISSA
true or false ?? an even two bit parity checker will output a parity error if data A=LOW data , B=HIGH. parity bit = HIGH