Answered: Q1; If a system has 30J of heat added…

Q1; If a system has 30J of heat added to it, and the total change in its internal energy is 10J, how much work does it do? a- 70 J b- 0.0 J c- 10J d- 20 J e- 10 J

Sustainable Energy

2nd Edition

ISBN:9781337551663

Author:DUNLAP, Richard A.

Publisher:DUNLAP, Richard A.

Chapter20: Hydrogen

Section: Chapter Questions

Problem 7P

See similar textbooks

Related questions

Q: A 1 lbm/s fluid enters a machine at 170 m/s. 800 kPa, and with a specific volume of 0.3 m³/kg. The…

A: Determine workdone by the fluid?

Q: Kerosene flows at 25 ° C, at a rate of 1200 L / min, from the lower tank (A) to the upper tank (B)…

A: Given data Q=1200 L/min=0.02m3/sA=π4d2=π4×0.0482 =1.809×10-3m2Velocity at pipe exit,…

Q: A 50-meter steel tape was used in laying-out a distance of 550.55 m. The tape was standardized at…

Q: 17-A refrigerator is to remove heat from the cooled space at a rate of 300 kJ/min to maintain its…

A: Let us estimate the Input power required by the refrigerator.

Q: An electric heater supplies (R+2.5)kW of power in the from of heat to water. If in 5.5 hours, 350kg…

A: Given data- Power (P) = (R+2.5)kW=(83+2.5)kW=85.5kW Time (t) = 5.5 hours Mass of water (m) = 350kg…

Q: Home Work Example: For the system shown in Figure calculate the height H of the oil at which the…

A: Given:- The specific gravity of the oil = 0.8 The air pressure = 30 kPa The width of the gate = 0.6…

Q: A closed container contains 1.Sm high of water, 2.5m high of oil (SG - 0.8), an unknown liquid (SG =…

A: Given data in question Depths of fluids Water Specific gravity of oil Pressure at top 17 kPa To…

Q: A refrigerator is to remove heat from the cooled space at a rate of 300.74 kJ/min to maintain its…

A: A type of elastic collision in which two objects of equal mass initially move in the same direction…

Q: A steel pipe is having an ID of 13.25" is to be designed to carry 48,000 bbl of oil per day from a…

A: We have to determine the value of the actual power requirement (in hp) if the efficiency is 65% and…

Q: A liquid of specific gravity SG = 1.62 flows in a 75 mm diameter horizontal pipe. The total energy…

A: Specific gravity of liquid, SG =1.62Diamteter of pipe, D=75mm =0.075mThe total energy at a point, E…

Q: Calculate the stopping sight disance for a design speed of 1000 kmph. Take the total reaction time…

Q: A fluid with a kinematic viscosity 1500 ft2/sec flows with an average velocity, v = 200 ft/sec…

A: Given: The kinematic viscosity is ν=1500 ft2/s. The average velocity is v=200 ft/sec The inside…

Q: 2. A cup of tea is prepared in a preheated cup with hot water so that the temperature of both the…

A: Answer: a. The temperature of the tea after 6 minutes is 106o F. b. The time required for the tea to…

Q: 1. A block of woods floats in water with 50 mm projecting above the water surface. When placed in…

A: Question 1: Given: Projection of wood in water=50 mmSpecific gravity of glycerin=1.35Projection of…

Q: The air in a certain room 150’ x 50’ x 12’ tested 0.2% CO2. Fresh air containing 0.05% CO2 was then…

Q: exchanger using 250 kPa steam of 90% quality. The heat losses to the surrounding air have be…

A: Given:- quantity of light oil =2m3/min temperature heated= 20 degree Celsius to 100 degree Celsius…

Q: 1. Steam at 2.0 kPa is saturated at 17.5C. In what state will the steam be at 40C if the pressure is…

A: Given data- 1. Case-(a) Steam at 2.0 kPa is saturated at 17.5C Case-(b) Temperature=40C , pressure…

Q: ghboring house. They reduce their flow rate so that the windows do not break, which wo e the inside…

A: According to given data A home is on fire, and to prevent its spread to the next house,…

Q: 1. Which of the following best approximates the acceleration of block Bas it glides along the floor?…

A: NOTE: As per our company guidelines we are supposed to answer ?️only first 3️⃣ sub-parts. Kindly…

Q: The machine parameters of the 1 hp, three phase, 60 Hz, four pole, 200 V induction machine are as…

Q: roblem 3- 104 Vater in a tank is pressurized to 80 cmHg. Determine the total force per meter ridth…

A: Calculate the pressure at B and A using hydrostatics then force can be calculated as area of…

Q: The compressed air requirements of a textile factory are met by a large compressor that draws in 0.6…

A: Q = 0.6m3/s g= 9.81m/s2 l (length) = 83m mu = 2*10-5 kg/m-s D (diameter) =30cm = 0.3m & r =…

Q: The Energy Efficiency Rating (EER) of an air-conditioning unit is defined asthe ratio of the heat…

A: Given data, Heat removed by one ton of A.C = 12,000 Btu/h Energy used = 2410 Watts. Capacity of A.C…

Q: Steam enters a long, horizontal pipe with an inlet diameter of D1=12 cm with a velocity of 2 m/s.…

A: mass flow rate is (density *Q) that is (density*AV) so Q=(3.14*.12*.12*2/4)*_(1/0.25799) =.0877kg/s

Q: 13. In the treatment of 25 x 10³ m³/day of water, the amount of chlorine used is 15 kg/day. The…

A: Asked: To compute the chlorine demand. Given: Flow rate = 25×103 m3/day Amount of chlorine used or…

Q: certain fluid has an enthalpy 1800 KJ/kg and 500 KJ/kg work flow. Find the internal energy.

Q: All For laminar flow over a flat plate, the local heat transfer coefficient h, is known to where x…

Q: Probiem 5: A liquid of specific gravity 1.7 flows in a 60-millimeter horizontal pipe. The total…

Q: ntly), but with 10 kg of air at 800 kPa, heated at constante pressure up to 400°C. Use the values…

Q: Heavy fuel oil flows through 3 km of cast iron pipe having a diameter of 250 mm. If the volumetric…

Q: Q2: A compounded impulse turbine has two rows of moving blades separated by a fixed row of blades.…

Q: Gasoline (T=50 degrees F) is pumped from the gas tank of an automobile to the carburetor through a…

A: Given :

Q: A fan is to be selected to ventilate a bathroom whose dimensions are 2 m × 3 m × 3 m. The air…

Q: The inlet and exit temperatures of the air expanded at an adiabatic turbine are 50 Cand -30 C,…

Q: Determine the work done by an electric motor lifting an elevator weighing 4 kN through five floors;…

A: Given: Weight of lift, W = 4 kN = 4000 N Number of floors, n = 5 Distance between each floor, d = 3…

Q: The enthalpy of combustion of benzoic acid (C6 H5 COOH) is commonly used as the standard for…

A: Some compounds release more energy than others in combustion reactions. Combustion enthalpy can be…

Q: A closed tank containing hot air has an initial internal energy of 400 kJ. During the next 5 min,…

A: The given data is: The initial internal energy=400 kJ Heat loss rate=1.5 KW The electrical power…

Q: nturi wine aerator is filled continuously from a bottle so that the le height, h = 4 cm, above the…

A: According to given data A Vinturi wine aerator is filled continuously from a bottle so that the…

Q: A 75 gal. electric hot water heater provides 9000 Watts of power to heat water. If the heater is…

A: Solution: Given Data: Power=9000 watts Initial temp= 50° F The amount of heat required to heat…

Q: A liquid whose specific gravity is 2.0, is flowing in a 50mm diameter pipe. The total head at a…

Q: If the work done 10000 cal, and the initial pressure 100 atm, when the ideal gas | expand…

A: Introduction : The general gas equation, commonly known as the ideal gas law, is the state equation…

Q: In a normal refrigeration cycle, the vapor pressure for refrigerant R-134aentering the compressor is…

A: Given:- Refrigerant-R-134a vapor pressure=19.3 pounds per sq in gauge reading condensing…

Q: The city of Springfield (where the Simpsons live) has finally decided to put the perpetually burning…

A: Bernoulli's principle : Daniel Bernoulli's principle asserts that when the speed of a flowing fluid…

Q: 1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28…

Q: One single phase energy meter operating on 230 V and 5 A for 5 hours makes 1940 revolutions. Meter…

Concept explainers

Thermal Processes

Some of the key areas where thermal processes find their application are:

Question

Q1; If a system has 30J of heat added to it, and the total change in its internal energy is 10J, how much work does it do? a- 70 J b- 0.0 J c- 10J d- 20 J e- 10 J

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Answer

VIEW

Answer

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water falls from a height of 500 m and the mass of water is 50 kg. What is approximately the rise in temperature of water at the bottom if the whole energy is used to heat the water? Specific heat of water is 4.18 kJ/kg-deg C. O 5000 deg C O 1173 deg C O 500 deg C O 0.23 deg C O none of the above
Calculate the specific heat of the material in J/g-deg C if material of 10 kilograms raises by 2 deg C when 2000 joules of heat is added. O 100 O 50 O 0.1 O 0.2 O none of the above
Question 2 Lauren has worker bullding her house on a hot summer day. She prepares a drink for them by adding a certain amount of ice at 0.0 °C to 1.8 kg of tea, initially at 80°C. How much ice in kilograms does she need to get the iced tea to be at final temperature of 10C? The heat of fusion of ice is 333 kJ/kg, specific heat of ice is 2100 J/kg. "Cand that of tea is 4186 Jkg. C 1.0 kg 15 kg O 12 kg
A certain fluid has an enthalpy 1800 KJ/kg and 500 KJ/kg work flow. Find the internal energy.
Q2/ How much heat does 50g of aluminum give off as it cools from 100c° to 10c°? for aluminum c=88 J/Kg.c°.
A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet to a certain nozzle, the specific enthalpy of the fluid is 3320 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the specific enthalpy is 2530 kJ/kg. The nozzle is horizontal, and the heat supply, the heat loss, the work input, and the work output to or from the nozzle are all negligible. (a) Determine the velocity at the nozzle exit
Question 3 A 2L, 4-stroke, 4-cylinder petrol engine has a power output of 113.9 kW at 5500 rpm and a maximum torque of 235 N-m at 3000 rpm. When the engine is maintained to run at 5500 rpm, the compression ratio and the mechanical efficiency are measured to be 8.9 and 83.2%, respectively. Also, the volumetric efficiency is 93.1 %, and the indicated thermal efficiency is 43.76 %. The intake conditions are at 36.9 °C and 1.00 bar, and the calorific value of the fuel is 44 MJ/kg Determine the Air-Fuel ratio in kg/kgf at 5500 rpm. Use four (4) decimal places in your solution and answer.
Your answer is partially correct. An insulated Thermos contains 110 cm3 of hot coffee at 83.0°C. You put in a 15.0 g ice cube at its melting point to cool the coffee. By how many degrees has your coffee cooled once the ice has melted and equilibrium is reached? Treat the coffee as though it were pure water and neglect energy exchanges with the environment. The specific heat of water is 4186 J/kg-K. The latent heat of fusion is 333 kJ/kg. The density of water is 1.00 g/cm³. Number i 20 Units C°
6.0 g of cream at 13.2 °C are added to an insulated cup containing 150.0 g of coffee at 92.9 °C. Calculate the equilibrium temperature of the coffee. You may assume no heat is lost to the cup or surroundings, and that any physical properties of cream and coffee you need are the same as those of water. Be sure your answer has 3 significant digits.
2. A parallel-plate capacitor initially has a capacitance of 100 F. What will be the capacitance if the distance between the plates is doubled?
A refrigerator absorbs 5 kJ of energy from a cold reservoir and rejects 8 kJ to a hot reservoir. (a) Find the coefficient of performance of the refrigerator. (b) The refrigerator is reversible and is run backward as a heat engine between the same two reservoirs. What is its efficiency?
Calculate the change in a 5-m long copper wire when its temperature changes by 120 oF. Thecoefficient of thermal expansion for copper is approximately 17 x 10-61/oC. Express your answerin SI units.