Question 3 A 2L, 4-stroke, 4-cylinder petrol engine has a power output of 113.9 kW at 5500 rpm and a maximum torque of 235 N-m at 3000 rpm. When the engine is maintained to run at 5500 rpm, the compression ratio and the mechanical efficiency are measured to be 8.9 and 83.2%, respectively. Also, the volumetric efficiency is 93.1 %, and the indicated thermal efficiency is 43.76 %. The intake conditions are at 36.9 °C and 1.00 bar, and the calorific value of the fuel is 44 MJ/kg- Determine the Air-Fuel ratio in kg/kgf at 5500 rpm. Use four (4) decimal places in your solution and answer.

Question 3 A 2L, 4-stroke, 4-cylinder petrol engine has a power output of 113.9 kW at 5500 rpm and a maximum torque of 235 N-m at 3000 rpm. When the engine is maintained to run at 5500 rpm, the compression ratio and the mechanical efficiency are measured to be 8.9 and 83.2%, respectively. Also, the volumetric efficiency is 93.1 %, and the indicated thermal efficiency is 43.76 %. The intake conditions are at 36.9 °C and 1.00 bar, and the calorific value of the fuel is 44 MJ/kg- Determine the Air-Fuel ratio in kg/kgf at 5500 rpm. Use four (4) decimal places in your solution and answer.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A flocculator tank has a volume of 2800 m³. The temperature of water in the tank is 15°C, and the average velocity gradient maintained in the tank is 100/s. The temperature of water is reduced to 5°C, but all other operating conditions including the power input are maintained as the same. The decrease in the average velocity gradient (in %) due to the reduction in water temperature is (round off to nearest integer). [Consider dynamic viscosity of water at 15°C and 5°C as 1.139 × 10-³ N-s/m² and 1.518 x10-3 N-s/m², respectively]
H.W2/3.4/Page(91)/ The local atmospheric pressure is 91 kPa. A gauge on an oxygen tank reads a pressure of 250 kPa gauge. What is the pressure in the tank in kPa abs?
Question 4 of 10 0/1 E View Policies Show Attempt History Current Attempt in Progress In a diesel engine the fuel is ignited when it is injected into hot compressed air, heated by the compression itself. In a typical high-speed diesel engine, the chamber in the cylinder has a diameter of 10.7 cm and a length of 13.4 cm. On compression, the length of the chamber is shortened by 12.7 cm (a “5-inch stroke"). The compression of the air changes its pressure from 1.00 to 39.5 atm. The temperature of the air before compression is 391 K. As a result of the compression, what will be the final air temperature (in Kand °C) just before the fuel injection? temperature = K = i °C eTextbook and Media Hint Assistance Used Determine the volume change as a way to get a handle on the new temperature. What equation relates pressure, temperature, and volume? The volume of the cylinder = z r² (height). Remember that the radius is half the diameter. Save for Later
If the specific gravity of the gasoline is 0.68, determine the pressure at the gasoline-water interface. Express the pressure in units of (a) lb/ft2, (b) lb/in2, and (c) as a pressure head of water in feet.
Assuming smooth contact surfaces, determine the reactions A, B, C and D on the cylinders as shown in the fig. Show your solutions in two ways. W 200 lb We400 lb to 5.6'
PROBLEM 3. The assembly shown constructed from a steel bolt with a diameter of 8 mm and fits and a magnesium sleeve with an inner diameter of 10 mm and an outer diameter of 12 mm. The length of the sleeve is 150 mm. The assembly is originally at a temperature of T1 temperature is raised to a final value of T2 = 120°C. If there is gap of 0.1 mm between sleeve and the rigid washer at end B before the heating, determine the average normal stress in the bolt and the = 20°C and then the sleeve. Est = 200 GPa, Emg = 44.7 GPa, a,t = 14(10°)/°C, amg = 26(10)/"C. Rigid washers 150 mm 0,1 mm
EN.3060 - Transport Phet Consider the system shown below in which a rod is contained within a coaxial cylinder. The system is aligned vertically. The rod has a radius Ri and the outer cylinder has a radius of R2. The region between the rod and outer cylinder contains an incompressible Newtonian liquid that has a density p and viscosity u. The rod is being moved in the positive z-direction at a constant velocity V while the outer cylinder is stationary. Assume the liquid is in steady fully developed laminar flow and there is no pressure gradient acting on the liquid in the direction in which the rod is moving. (a) Write the simplified forms of the Continuity and Navier-Stokes Equations in cylindrical coordinates that will be used for solving for the velocity profile in the liquid. (b) Write the applicable boundary conditions that will be used to solve for the velocity profile. (c) Solve for the velocity profile v in terms of r, R1, R2, V, p, g and u. (d) Assume the rod has a radius RI=3…
Gasoline at 20°C is pumped through a smooth 12-cm-diameter pipe 10 km long, at a flow rate of 75 m'/h (330 galpain). The inlet is fed by a pump at an absolute pressure of 24 atm. The exit is at standard atmospheric pressure and is 150 m higher. Estimate the frictional head loss h, and compare it to the velocity head of the flow V/(2g). (These numbers are quite realistic for liquid flow through long pipelines.)
Mechanics of Deformable Bodies A solid steel shaft 3 m long is stressed to 30 MPa when twisted by 2°. Compute the required diameter for this condition and the power transmitted (in HP) by the shaft if it rotates at 10 rad/sec.
10-kg of R-134a fill a 1.348-m3 rigid container at an initial temperature of 240oC. The container is then heated until the pressure is 200 kPa. Determine the final temperature and the initial pressure
A flocculate is designed to achieve a velocity gradient of 50 s with a volume of 3000 m the viscosity of the water is 1.1x10 Pa-sec. The coefficient of drag paddle is 1.8 and paddle tip velocity is 0.8 m/sec. The relative velocity of the paddle is with respect to water is 70% of paddle tip velocity. The mass density of water is 1002 kg/m'. Calculate the power required for paddles and total area of the paddle blades. a) 7.57 kW and 45.98 m² b) 9.12 kW and 60.53 m? c) 8.25 kW and 52.10 m d) 6.38 kW and 39.59 m
Gasoline is mixed with 8 ft of kerosene so that the volume of the mixture in the tank becomes 12 ft. Determine the specific weight and the specific gravity of the mixture at standard temperature and pressure.