All For laminar flow over a flat plate, the local heat transfer coefficient h, is known to where x is the distance from the leading edge (x =0) of the plate. What is -1/5 vary as x 3 the ratio of the average coefficient between the leading edge and some location x on the plate to the local coefficient at x? for velocity equation u-2-0.43x+x² Plot the local heat transfer coefficient over a 0.8 cm length(take T-35c)

All For laminar flow over a flat plate, the local heat transfer coefficient h, is known to where x is the distance from the leading edge (x =0) of the plate. What is -1/5 vary as x 3 the ratio of the average coefficient between the leading edge and some location x on the plate to the local coefficient at x? for velocity equation u-2-0.43x+x² Plot the local heat transfer coefficient over a 0.8 cm length(take T-35c)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

No. 1. (10 Pts) An aluminum pipe with a length of 60 m at a temperature of 10°C rests freely on the ground. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. (a) At what temperature (degrees Celsius) will the aluminum pipe be 15 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are aa=23x10-6/"C and as=12x10-6/ c, respectively.) (b) What is the axial stress developed in the aluminum pipe when the temperature was increased? 5 mm Aluminun Steel Figure No. 1
Consider the problem of draining a hemispherical tank of radius H* feet that is full of water and has a circular drain hole of radius 3 inches at the bottom. How long will it take for the tank to empty? dv When the change volume is = -kA/2gh(t) A is the constant cross sectional area of the opening; and k is a constant determined by the viscosity of the fluid dh dt H H-h dV 1 dt dt ar² Note: Draining a hemispherical tank. Take H* as a last two digits of your ICEM ID, if last two digits less than 10 take H= 18 feet
Q2// Consider a special ball made of steel (p- 5000 kg/m', Cp- 300 J/kg. k, A= 60 m²). The initial temperature of the ball is 300 K. It is immersed in a large oil tank at 400 K. The convective heat transfer coefficient, h at the sphere surface is 3000 W/m³. k. Assume that there is no radial temperature gradient inside the ball. Use Euler's method to find the temperature of the sphere at t = 15 sec after it was immersed in the oil tank. Use a step size of h= 5 sec. The energy balance equation of the ball is given by the following equation: dT pCp -=-hA(T-T₂) dt
An increase in pressure of a liquid from 7.5 MPa to 15 MPa results into 0.2 percent decrease in its volume. Determine the coefficient of compressibility of the liquid.
A flow of liquid is discharged from a long horizontal pipe of circular cross-section into theatmosphere. Sketch the typical appearance of(i) a laminar jet(ii) a turbulent jet.Explain their forms and the differences between them.Define the loss coefficient K, used in the analysis of pipe systems. Give three examples of distinct elements in pipe systems which lead to losses, explaining briefly in each case why the losses occur.You want to draw water from a stream running down a hill behind your house at a rate of 3 litres /s.To hand you have 30m of commercial steel tubing of inside diameter 30mm. At what vertical level above the house should you dam the stream to draw off the water?.
1. When the force of 3 mN is applied to the plate the line AB in the liquid remains straight and has a velocity of 0.6x103 m/s. If the surface area of the plate in contact with the liquid is 0.6 m2, determine the approximate viscosity of the liquid. В в B B' 3 mN 4 mm A
6c. Explain the fundamental reason for shear viscosity oxz by considering a fluid flowing along the x-axis with velocity v(z). How do thermal effects or turbulent flows lead to viscosity?
A 0.6 m square glass plate slides on a plane with a slope of 30° from the horizontal (Figure 1.2). Knowing that the plate weighs 30 N and that it acquires a constant speed of 5 cm/s, it is asked: determine the dynamic viscosity of the film 0.1 mm lubricant, which is between the plates. Assume the velocity diagram linear in the fluid film). (R: 0.0833 Ns/m2) 5cm/s Figure 1.2 0.1 mm
1. When the force of 3 mN is applied to the plate the line AB in the liquid remains straight and has a velocity of 0.6x10-3 m/s. If the surface area of the plate in contact with the liquid is 0.6 m2, determine the approximate viscosity of the liquid. В B' 3 mN 4 mm A
A steel tape with a coefficient of linear expansion of 0.0000116/oC is know to be 50m long at 20oC. The tape was used to measure a line which was found to be 532.28 meters long when the temperature was 35oC. Determine the following:a) Temperature correction per tape length.b) Temperature correction for the measured line.c) Correct length of the line.
(a) Glycerine at 25 °C flows through a straight copper tube (D = 73.8 mm), at a flow rate of 180 L/min. Calculate the pressure difference between 2 points which are 25.8 m apart, if the first point is 0.68 m below the second point. Gven: At 25 °C density and dynamic viscosity for glycerine is 1286kg/ and 0.96 Pa.s respectively(b) If benzene at 50 °C is used in question (a) above instead of glycerine, evaluate the new pressure difference. ...
Compute the pressure heat at m, in feet of fluid A, indicated by open manometer in figure 2 below when (a) Fluid A is oil (sp gr 0.851), the gage liquid is carbon tetrachloride (sp gr 1.51), y=30.15 in, z=3051 in. (b) Fluid A is molasses (sp.gr 1.50), gage liquid is water, y=3.51 ft, z=1.15 ft