Write the direct stress formula in its three forms and explain the meaning of each one.
To write: Direct stress formula in three forms and explain the meaning of each one.
Explanation of Solution
The three forms direct stress formula are as follows:
1.
Here,
It means the average normal stress in a member is equal to axial normal force acting on it divided by the area of cross-section on which the normal force acts. It is used to calculate the average stress developed in a member having a cross- sectional area A, when an external force of magnitude P act.
2.
Where,
P is the axial load capacity.
A is the cross-sectional area of the member.
This form of the formula is used to calculate the maximum load capacity (maximum permissible axial load) of a member having maximum permissible stress,
3.
Where,
P is the axial load capacity.
A is the cross-sectional area of the member.
This formula is applicable for Analysis of load capacity.
Want to see more full solutions like this?
Chapter 9 Solutions
Applied Statics and Strength of Materials (6th Edition)
Additional Engineering Textbook Solutions
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Manufacturing Engineering & Technology
Mechanics of Materials (10th Edition)
Engineering Mechanics: Statics
Engineering Mechanics: Statics & Dynamics (14th Edition)
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
- Use the given information and calculate the stress. (Please add FBD if possible)arrow_forwardCan you calculate the stress for the remaining point instead of point 1 only?arrow_forwardExplain the Mohr’s circle for stress and write down the procedure of drawing Mohr’s circle and solving problems through it.arrow_forward
- How is the state of plane stress at the point uniquely represented?arrow_forwardA. For Problems 10–56 through 10–83, determine the principal stresses and the maximum shear stress using Mohr’s circle. The following data sets give the stresses on the initial stress element. Perform the following operations: JUST DO PROBLEM 10-56 PLEASE (a) Draw the complete Mohr’s circle, labeling critical points including σ1, σ2, τmax, and σavg. (b) On Mohr’s circle, indicate which line represents the x-axis on the initial stress element. (c) On Mohr’s circle, indicate the angles from the line representing the x-axis to the σ1-axis and to the τmax-axis. (d) Draw the principal stress element and the maximum shear stress element in their proper orientation relative to the initial stress element.arrow_forwardHow many independent stress components are needed to define the stress state of a point in 3-D?arrow_forward
- Which of the following is true for an infinitesimal stress element? (T in the options below refers to tau, or shear stress) (a) Txy = Tyz (b) Txy = Tyx (c) Txy = Txz (d) Tx = Tyarrow_forwardWhat is the maximum normal stress?arrow_forwardPlease answer as per question and in clear handwriting. The state of stress at a point in a structure is shown in the following figure.Decide:(a) The forces acting on an element oriented at an angle in the directioncounterclockwise θ = 15° from the x-axis (Show the results in a sketch ofcorrectly oriented)(b) find the main stresses (Show the results on a sketch ofcorrectly oriented)arrow_forward
- fill in the blank please For any arbitrary plane stress components, σx, σy and τ xz, the orientations of principle and maximum shear stress planes will always be( ) degrees apart when considering the stress element and ( ) degrees apart in the circle representation.arrow_forwardA figure shows a state of stress; determine the shearing stresses and normal stresses after the element has been rotated (a) 40° clockwise, (b) 25° counterclockwise.arrow_forwardCalculate the stress parallel to the inclined plane AB. Report your answer as a positive number.Answer: τnt= Enter your answer in accordance to the question statement ksi.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY