Concept explainers
Representing a transmission line by the two-port network, in terms of ABCD parameters, (a) express
(a)
_________ (b)
(a)
The sending end voltage in the form of receiving end parameters.
Answer to Problem 5.1MCQ
Explanation of Solution
Given:
A two port network having ABCD parameter is shown below.
Calculation:
For transmission line, input-output terminal voltage and current in the form of
ABCD parameter is given by,
Hence, from the above relation, sending end voltage is given by
(b)
The sending end current in terms of receiving end parameters.
Answer to Problem 5.1MCQ
Explanation of Solution
Given:
A two port network having ABCD parameter is shown below.
Calculation:
For transmission line, input-output terminal voltage and current in the form of
ABCD parameter in given by,
Hence, from the above relation, sending end current is given by
Want to see more full solutions like this?
Chapter 5 Solutions
Power System Analysis and Design (MindTap Course List)
- c) Two power system transmission engineers designed a transmission system. One used the lumped parameters and the other used distributed parameters in their transmission line analysis. Could you kindly evaluate the differences of these parameters chosen by the two engineers?arrow_forward4.Please solve a,b,c please be detailed in y-bus calculationsarrow_forwardRepresenting a transmission line by the two-port network, in terms of ABCD parameters, express Vs, which is the sending-end voltage, in terms of V, which is the receiving-end voltage, and I, the receiving-end current,arrow_forward
- in planner transmission line the controlling of the characteristics impedance Zo is possible by controlling its _________ ? width of substrate dimension height of the substrate permittivity of the substratearrow_forwardWith the system shown in the figure, use 100MVA as system base, and 230 kV as base voltage along the transmission line. For the same system in the figure, build the Y-bus matrix without the Load. 1. What is the element Y11? Provide the susceptance value 2. What is the element Y22? Provide the susceptance valuearrow_forwardFor a 4 - bus network, Zpus is shown below. r0.71660 0.60992 0.53340 0.58049] 0.60992 0.73190 0.64008 0.69659 0.53340 0.64008 0.71660 0.66951 Lo.58049 0.69659 0.66951 0.76310 Z Bus = j. When the refernce is changed from node (n) to node (1), Find: Z22 of the new impedance matrix Zausnew is: Select one: O a. 0.1832 O b. 0.22866 O c. 0.10688 O d. 0.13611 e. Nore of thesearrow_forward
- The A parameter of a transmission line is O a. Equal to D O b. Equal 0 c. Equal to B O d. Equal to Carrow_forward4. A 400 kV, 150 km long OHL with parameters R-0.017 2/km, X₁50.27 2/km and X 94520 2/km is used to transmit 1800 MW at 0.9 power factor (lag). Calculate the sending end voltage using: a) Simple short-line R/L model b) Full distributed line modelarrow_forwardWith the system shown in figures, use 100MVA as system base, and 230 kV as base voltage along the transmission line. 1. Based on the system diagram with buses labelled accordingly what should be the rank of the square Y-bus matrix? 2. Build the Y-bus matrix without the Load. What is the element Y11 in susceptance value? 3. Build the Y-bus matrix without the Load. What is the element Y22 in susceptance value? 4. Build the Y-bus matrix without the Load. What is the element Y12 in susceptance value? 5. If you are to convert the real power load to a shunt conductance, what is the value of the conductance in per unit?arrow_forward
- Transmission line parameters.arrow_forward3. In LQR controller technique it can increase the input signal by a. Reducing diagonal elements of Q matrix b. Reducing diagonal elements of R matrix c. Increasing diagonal elements of R matrix d. Increasing diagonal elements of Q matrix Maximum solution- HAY. -LAZATIV a. Increase rise time b. Decrease rise time c. Increase settling time d. Decrease settling time None of all above trol provi problem 5. In LQR controller technique decreasing value of the element q12 in Q matrix canarrow_forward(b) In a particular implementation of ADSL2+, 400 downstream subchannels are being used to achieve a data rate of 10.4 Mbit s-1. If 75 subchannels are using 1024-QAM, 125 are using 64-QAM and 100 are using 16-QAM, what modulation scheme must the remaining channels use, assuming they all use the same scheme? Show all your workingsarrow_forward
- Power System Analysis and Design (MindTap Course ...Electrical EngineeringISBN:9781305632134Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. SarmaPublisher:Cengage Learning