Concept explainers
The cylinder CD of the assembly is heated from T1 = 30°C to T2 = 180°C using electrical resistance. At the lower temperature T1 the gap between C and the rigid bar is 0.7 mm. Determine the force in rods AB and EF caused by the increase in temperature. Rods AB and EF are made of steel, and each has a cross-sectional area of 125 mm2. CD is made of aluminum and has a cross-sectional area of 375 mm2. Est = 200 GPa, Eal = 70 GPa, and αal =23(10-6)/°C.
Probs. 4–84/85
Trending nowThis is a popular solution!
Learn your wayIncludes step-by-step video
Chapter 4 Solutions
Mechanics of Materials (10th Edition)
Additional Engineering Textbook Solutions
Applied Statics and Strength of Materials (6th Edition)
Applied Fluid Mechanics (7th Edition)
Engineering Mechanics: Dynamics (14th Edition)
Engineering Mechanics: Statics & Dynamics (14th Edition)
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
- 2. The bar has a cross-sectional area A, length L, modulus of elasticity E, and coefficient of thermal expansion a. The temperature of the bar changes uniformly along its length from TA at A to Tg at B so that at any point x along the bar T = TA + x(TB - TA)/L. Determine the force the bar exerts on the rigid walls. Initially no axial force is in the bar and the bar has a temperature of TA. A B TA TBarrow_forwardThe cylinder CD of the assembly is heated from T1 = 30°C to T2 = 180°C using electrical resistance. At the lower temperature T1 the gap between C and the rigid bar is 0.7 mm. Determine the force in rods AB and EF caused bythe increase in temperature. Rods AB and EF are made of steel, and each has a cross-sectional area of 125 mm2. CD is made of aluminum and has a cross-sectional area of 375 mm2. Est = 200 GPa, Eal = 70 GPa, and aal = 23(10-6)>°C.arrow_forward2. The bar has a cross-sectional area A, length L, modulus of elasticity E, and coefficient of thermal expansion a. The temperature of the bar changes uniformly along its length from TA at A to TB at B so that at any point x along the bar T = TA + x(TB – TA)/L. Determine the force the bar exerts on the rigid walls. Initially no axial force is in the bar and the bar has a temperature of TA. A B TA TBarrow_forward
- 3) The plug has a diameter of 30 mm and fits with a rigid sleeve having an inner diameter of 32 mm. Both the plug and the sleeve are 50 mm long. Determine the axial pressure P that must be applied to the top of the plug to cause it to contact the sides of the sleeve. Also, how far must the plug be compressed downward to do this? The plug is made from a material for which E = 5 MPa, v = 0.45. Parrow_forwardThe wires AB and AC are made of steel, and wire AD is made of aluminum. Before the 300 kN force is applied, AB and AC are each 150 mm. long and AD is 100 mm. long. If the temperature is increased by 30°C, determine the force in each wire needed to support the load. Take Est = 200 GPa, Eal = 70 GPa, st = 12 (10") / °C, aal = 23 (10") / °C. Each wire has a cross-sectional area of 0.02 mm². B 100 mm 45° 45° 150 mm 150 mm A 300 kNarrow_forwardThe bar has a cross-sectional area A, length L, modulus of elasticity E, and coefficient of thermal expansion a. The temperature of the bar changes uniformly along its length from TA at A to TB at B so that at any point x alongthe bar T = TA + x(TB - TA)>L. Determine the force the bar exerts on the rigid walls. Initially, no axial force is in the bar and the bar has a temperature of TA.arrow_forward
- The inner ring A has an inner radius r1 and outer radius r2. The outer ring B has an inner radius r3 and an outer radius r4, and r2 7 r3. If the outer ring is heated and then fitted over the inner ring, determine the pressure between the two rings when ring B reaches the temperature of the inner ring. The material has a modulus of elasticity of E and a coefficient of thermal expansion of a.arrow_forwardThe 40ft long A-36 steel rails on a train track are laid with a small gap between them to allow for the thermal expansion. Determine the required gap & so that the rails just touch one another when the temperature is increased from T₁=20° F to T₂=90°F. Using this gap, what would be the axial force in the rails if the temperature were to rise to T3=110°F? The cross-sectional area of each rail is 5.10 in²arrow_forwardA steel bar 300 mm long, 50 mm wide and 40 mm thick is subjected to a pull of 300 kN in the direction of length. Determine the change in volume. Take E = 2x105 N/mm2and μ= 0.25.arrow_forward
- The three rods are made of A-36 steel and form a pin-connected truss as shown. The assembly is stress- free at 50 °F. Determine the force in each bar when the temperature of the assembly is increased to 110 °F. The cross-sectional area of each bar is 2.5 in². 5 ft 4 ft D 5 ft 3 ft 3ftarrow_forwardThe 58-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed the clamp when the temperature is T₁ = 20°C. (Figure 1) Figure 100 mm 150 mm Part A If the 304-stainless-steel carriage bolts of the clamp each have a diameter of 9 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the force in the cylinder when the temperature rises to T₂ = 130°C. Express your answer to three significant figures and include the appropriate units. F = 2.37 Submit μÀ ^ Provide Feedback KN WX Previous Answers Request Answer ? X Incorrect; Try Again; 3 attempts remaining Next >arrow_forwardThe rod BD is made of materia with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2=1042 N.m, answer the following questions: A B T2 N-m 0.4 m 0.1 m 0.3 m T1 N-m The polar moment of inertia of the rod BD is The maximum shear stress of the tube CA is The maximum shear stress of the assembly isarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY