Concept explainers
In the circuit in Figure P3.21, assume the source voltage and source current and all resistances are known.
a. Write the node equations required to determine the node voltages.
b. Write the matrix solution for each node voltage in terms of the known parameters.
(a)
Thenode equations required to obtain the node voltages.
Answer to Problem 3.21HP
The required node equations are
Explanation of Solution
Calculation:
The given diagram is shown in Figure 1
Apply KVL at the node
Apply KVL at the node
Conclusion:
Therefore, the required node equations are
(b)
The matrix solutions for each of the node voltages in terms of the known parameters.
Answer to Problem 3.21HP
The required node voltage equations are
Explanation of Solution
Calculation:
The equation (1) equation (2) in the matrix form is given by,
The determinant of the square matrix is given by,
The first determinant form of the matrix form is given by,
The second determinant is given by,
The expression to determine the node voltage
Substitute
The expression for the node voltage
Substitute
Conclusion:
Therefore, the required node voltage equations are
Want to see more full solutions like this?
Chapter 3 Solutions
Principles and Applications of Electrical Engineering
- A nonideal voltage source is modeled in FigureP3.72 as an ideal source in series with a resistance thatmodels the internal losses, that is, dissipates the samepower as the internal losses. In the circuit shown inFigure P3.72, with the load resistor removed so thatthe current is zero (i.e., no load), the terminal voltageof the source is measured and is 20 V. Then, withRL = 2.7 kΩ, the terminal voltage is again measuredand is now 18 V. Determine the internal resistance andthe voltage of the ideal source.arrow_forwardThe value of the equivalent voltage source at the A-B ends of the circuit in the figure is found in ………volts.arrow_forwardIn the circuit shown in Figure P3.5, the source andnode voltages areVS1 = VS2 = 110 VVA = 103 V VB = −107 VDetermine the voltage across each of the five resistorsarrow_forward
- Using mesh current analysis, find the currents i1 and i2 for the circuit of Figure P3.14.arrow_forwardProblem 3.6: Two batteries' terminal voltage versus load current droop lines are shown in Figure P3.6. Determine analytically the load current shared by each battery and the battery bus voltage if they share a total load current of (i) 500 A and (ii) 800 A. In the case of 500 A total load, verify your answers by a one-step method with the Battery-2 line redrawn backward as needed. 140 Battery-1 130 Battery-2 120 110 100 200 300 400 500 600 Load Current Amps FIGURE P3.6 Terminal Voltagearrow_forwardUsing mesh current analysis, find the currents I1, I2, and I3 in the circuit of Figure P3.17 (assume polarity according to I2).arrow_forward
- Question 3 (a) Briefly explain what is the per-unit systero. (b) A resistance of 60n is selected as the base resistance in a circuit consists of three resistors. If R, =1002, R, =30002 and %3D R, = 200 calculate the per-unit vahue of each resistance. %3D (c) A power of, P-25KW and a voltage of, E-2400V are selected as the base power and base voltage of a power system respectively. Calculate the value of the base impedance, Z, and the base current, I,. (d) A resistor bas a per-nnit value of 5.3. Given the base power is P=250KW, and the base voltage is E,-12470V, calculate the ohmic value (actual value) of the resistor. (e) A 4000 resistor caries a cucrent of 60A. Given the base valne of voltage, E, 4KV, the base value of power, P, 500KTF, the base value of current, I, =125.4, and the base value of resistor, 2, = 320 calculate the following: i The per-unit resistance. ii. The per-unit current. ii. The per-unit voltage across the resistor. iv. The per-unit power.arrow_forwardAfter solving for the total resistance, and the applied voltage being a given for the circuit, the next logical step is to .....? so that individual component voltages and currents can be found.arrow_forwardBasic Electrical EngineeringDraw symbols of electrical components. Note: You may use both IEC and NEMA symbols. - Conductors crossing but not connected- Conductors crossing and connected - DC source other than battery- DC generator- AC voltage source- Ideal current source- Ideal Voltage Source- Current Controlled Current Source- Current Controlled Voltage Source- Voltage Controlled Current Source - Voltage Controlled Voltage Sourcearrow_forward
- The equivalent circuit of Figure P3.73 hasVT = 35 V RT = 600Ω If the conditions for maximum power transfer exist,determinea. The value of RL.b. The power developed in RL.c. The efficiency of the circuitarrow_forwardIn Figure 3.5, is there a linear relationship between current and voltage? In Figure 3.5, what is the relationship between the slope of the plotline and the circuit resistance?arrow_forwardWhat approximation do we usually make in circuit theory? -A current-carrying particle is the current. -A current-carrying particle has no charge. -A current-carrying particle does't accelerate. -A current-carrying particle is mythical. -A current-carrying particle is massless Please see diagram for more details.arrow_forward
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,