Concept explainers
A
The maximum bending stress in the rod
Answer to Problem 15.1P
Explanation of Solution
Given Information:
Diameter of aluminum rod,
Mean diameter of the circular ring,
Modulus of elasticity for aluminum
The maximum bending stress in the rod is given by
Conclusion:
Therefore, the maximum bending stress in the rod is
Want to see more full solutions like this?
Chapter 15 Solutions
Applied Statics and Strength of Materials (6th Edition)
Additional Engineering Textbook Solutions
Engineering Mechanics: Statics & Dynamics (14th Edition)
Engineering Mechanics: Dynamics (14th Edition)
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Mechanics of Materials
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
- Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 ft, b=8.0 ft, c=4.0 ft, d=3.0 ft, w = 6.5 kips/ft and P = 45 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. a B a W B W C b d For this loading, calculate the reaction forces Ay and Ey acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) b C C P C D P Ľ E d E ·x Eyarrow_forward2. A shaft made of mild steel. The supported length of the shaft is 3 meters. It carries two pulleys each weighing (1500N) supported at a distance of 1 meter from the ends respectively. Calculate the maximum bending stress on the sample ? 1500 N 1500 N D -1m FIm- 3m RA Rgarrow_forwardCompute the maximum stress due to bending in a round rod 20 mm in diameter if it is subjected to a bending moment of 120 N-m.arrow_forward
- Calculate the maximum normal bending stress and the maximum shear stressarrow_forwardNeed correct solution. If C is the mid-point of PQ; What is the magnitude of bending moment at fixed end O?arrow_forwardThe rod has a diameter of 0.5 in. and a weight of 5 lb/ft. i) Calculate the torque and bending moment on the cross-section passing through B. ii) Calculate max shear stress and max bending stress on the cross-section B.arrow_forward
- A W360 × 72 standard steel shape is used to support theloads shown on the beam in Figure a. The shape is oriented sothat bending occurs about the weak axis, as shown in Figure b.Consider the entire 6 m length of the beam, and determine(a) the maximum tensile bending stress at any location along thebeam and(b) the maximum compressive bending stress at any locationalong the beamarrow_forwarddraw the shear and bending moment diagram. solve it correctly please. I will rate accordinglyarrow_forwardQUESTION 3 If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is W8 x 40. If the beam is 10 foot long and simply supported and has a concentrated load applied at x = 3 ft as shown below. • Generate the shear force and bending moment diagram in terms of P; • Based on the allowable maximum bending moment you just obtained above, calculate/ input the mazimm allowable value of the load P: please, pay attention to units, and calculate your answer to 1 decimal place.. 3 ft 7 ft kip.arrow_forward
- A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.arrow_forward(c) Calculate the maximum compressive bending stress (Express the stress in Pa or MPa ) and determine its location with respect to neutral axis.arrow_forwardA beam has a rectangular cross section 80 mm wide and 120 mm deep. It is subjected to a bending moment of 15 kN-m at a certain point along its length. It is made from metal with a modulus of elasticity of 180 GPa. Calculate the maximum stress on the section.arrow_forward
- Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning