Concept explainers
(a)
The volume fractions for the fiber and matrix in the laminate.
(a)
Answer to Problem 97SEP
The volume fractions for the fiber and matrix in the laminate are
Explanation of Solution
Write the equation for the rule of mixture for the composite material.
Here, modulus of elasticity of composite is
Write the equation to calculate the volume fraction of matrix.
Conclusion:
It is given that the component is suggested to be made from unidirectional carbon fiber composite. Therefore, the fiber layer will be carbon and the matrix layer will be epoxy.
Take the modulus of elasticity of carbon fiber to be
Substitute
Substitute
Thus, the volume fractions for the fiber and matrix in the laminate are
(b)
The volume fractions for the fiber and matrix in the laminate.
(b)
Answer to Problem 97SEP
The volume fractions for the fiber and matrix in the laminate are
Explanation of Solution
Write the equation to calculate the percentage in weight reduction.
Here, density of carbon composite is
Conclusion:
Refer Appendix I, "Important properties of the selected engineering materials" to obtain the densities of aluminum composite and carbon composite.
Substitute
Therefore, the carbon composite will be 43% lighter when compared to aluminum composite.
Want to see more full solutions like this?
Chapter 12 Solutions
Foundations of Materials Science and Engineering
- Why are composites used in engineering?arrow_forwardClassify the types of composite materials based on the matrix and reinforcement materials. Briefly explain the main characteristics of Polymeric Matrix Composites (PMC) and their engineering applications.arrow_forwardIt is desired to produce an aligned and continuous fiber-reinforced epoxy composite having a maximum of 50% fibers. A minimum longitudinal modulus of elasticity of 55 GPa and a minimum tensile strength of 1200 MPa are required. E-glass and carbon (PAN standard modulus) fibers are the possible candidates to select. In addition, assume the stress levels on the epoxy matrix at fiber failure are 70 MPa for E-glass fiber and 30MPa for carbon fiber, respectively. Which fiber meets the design requirement? Use the properties given in the Table below to evaluate your selection. Materials Epoxy matrix E-glass Carbon Modulus of Elasticity (GPa) 3.1 72.5 230 Tensile Strength (MPa) 69 3450 4000arrow_forward
- A continuous and aligned glass fiber-reinforced composite with modulus of elasticity of 55 GPa. The volume fiber fraction is 40 and the modulus of elasticity of the fiber is 75 GPa. Calculate the volume fraction of epoxy matrix if you know the modulus of elasticity of the modulus of elasticity of the matrix is 2.5 GPa and then determine the strain that is sustained by each phase under applied stress of 27 Mpa. (assume that the cross-section area is 150 mm2)arrow_forwardA composite with a vinyl ester (VE) matrix contains 2 vol% CNTS with the following characteristics: 1= 7 um, d= 50 nm, di = 4 nm, and EcCNT = 900 GPa. The modulus of the VE matrix is 1.9 GPa. %3D c. Find the Major Poisson's ratio for this composite using strength of materials approach. d. Find the in-plane shear modulus for this composite using strength of materials approach.arrow_forwardCompute the ultimate strength for a composite which uses Aramid fibers and Polyester matrix. The volume fraction of fibers is 45 % and matrix is 55 %. Note- use chart in imagearrow_forward
- What is the tenacity in gf of a 3.2 tex fiber den that ruptures under a load of 94.8 gf ? Provide your answer with two decimal positions and no unit. Answer:arrow_forwardNowadays, many cooking utensils are made of polymeric materials. However, people believe that heating plastic utensils would cause harm such as releasing toxic substances. Hence, people are looking for other alternatives to replace plastic. Choose ONE cooking utensil (spatula) and identify the suitable material that will satisfy its criteria. Justify your answer. Your discussion must include the interrelationship between structure-properties-processing of the selected cooking utensil.arrow_forwardDescribe three of the functions of the matrix in fibre- reinforced composites. With the aid of sketches compare and contrast the fatigue fracture appearance between an alloy that failed at a low fatigue load and one that failed at a high fatigue load. Propose and briefly describe one non-destructive method that can be used to detect small cracks on the surface of a metallic alloy.arrow_forward
- Please calculate UD composite material averaged mechanical constants EL: ET; VET. Gur Fiber and matrix properties are: E, = 240GP3; v, = 0.26; E = 2.6GPA; v = 0.38; fibers volume fraction V, = 0.48 Please use different methods and compare obtained results.arrow_forwardIf the tensile strength of the Kevlar 49 fibers is 3.8 GPa and that of the epoxy resin is 75.9 MPa, calculate the tensile strength of the composite material in Q3b(i). Calculate the fraction of load carried by the Kevlar 49.arrow_forwardWhat is the distinction between matrix and dispersed phases in a composite material? Contrast the mechanical characteristics of matrix and dispersed phases for fiber reinforced composites.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY