Electric Motors and Control Systems
2nd Edition
ISBN: 9780073373812
Author: Frank D. Petruzella
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 1.1, Problem 2RQ
a. Calculate the theoretical body current flow (inamperes and milliamperes) of an electric shockvictim who comes in contact with a 120 V energysource. Assume a total resistance of 15,000
b. What effect, if any, would this amount of currentlikely have on the body?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Q3:A: (a) A 10-hp 230-volt shunt-wound motor has rated speed of
1000 rpm and full-load efficiency of 86 percent. Armature-circuit
resistance, 0.26 ohm; field-circuit resistance, 225-ohms. If this motor
is operating under rated load and the field flux is very quickly
reduced to 50 percent of its normal value, what will be the effect
upon back emf, armature current and torque? What effect will this
change have upon the operation of the motor, and what will be
its speed when stable operating conditions have been regained?
An 8 pole, lap connected armature has 500 conductors and its generated e.m.f is 120V. If the
flux per pole is 20 mWb, then the speed of machine is,
3. (i) Three identical capacitors are connected in delta with 400 V. If the line current is 12 A
determine the capacitance of each of the capacitors. If the 0
60° then calculate the
power dissipation in kW when it is connected in STAR
ENGG_AC_Quiz-Format_01/2016-17_V02
(ii) Three coils each having resistance 6Q and inductance are connected in star with
415V. If the line current is 30 A, find the value of inductive reactance as well as
inductance value. If 0
45° then calculate the power dissipation in kW when it is
connected in Delta.
Chapter 1 Solutions
Electric Motors and Control Systems
Ch. 1.1 - Does the severity of an electric shock increase...Ch. 1.1 - a. Calculate the theoretical body current flow...Ch. 1.1 - Normally a 6 volt lantern battery capable of...Ch. 1.1 - Prob. 4RQCh. 1.1 - What circuit fault can result in an arc flash?Ch. 1.1 - Defineeach of the following terms associated...Ch. 1.1 - Explain why an arc flash is so potentially...Ch. 1.1 - State the piece of electrical safety equipment...Ch. 1.1 - Outline the safety procedure to follow when you...Ch. 1.1 - List three pieces of personal protection...
Ch. 1.2 - Prob. 1RQCh. 1.2 - Prob. 2RQCh. 1.2 - Prob. 3RQCh. 1.2 - List the seven steps involved in a...Ch. 1.2 - Prob. 5RQCh. 1.2 - Prob. 6RQCh. 1.2 - How are the standards contained in the...Ch. 1.2 - Explain the difference between a Code Article and...Ch. 1.2 - Prob. 9RQCh. 1.2 - Prob. 10RQCh. 1.2 - Prob. 11RQCh. 1.2 - Prob. 12RQCh. 1.2 - The voltage between the frame of a 3-phase 208...Ch. 1.2 - Prob. 2TCh. 1.2 - Prob. 3TCh. 1.2 - A hot stick is to be used to open a...Ch. 1.2 - An employee is contemplating using his lockoutlock...Ch. 1.2 - Prob. 1DTCh. 1.2 - Prob. 2DTCh. 1.2 - Why can birds safely rest on high-voltage...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
6–1C A mechanic claims to have developed a car engine that runs on water instead of gasoline. What is your resp...
Thermodynamics: An Engineering Approach
Assume the following vectors are already defined: V1=[302]V2=[214]V3=[5131]V4=[0.50.10.20.2] For each of the fo...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Locate the centroid of the area. Prob. 9-17
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
How is the hydrodynamic entry length defined for flow in a pipe? Is the entry length longer in laminar or turbu...
Fluid Mechanics Fundamentals And Applications
For the beam loading of Figure P334, draw the complete shearing force and bending moment diagrams, and determin...
Machine Elements in Mechanical Design (6th Edition) (What's New in Trades & Technology)
A pipe flowing light oil has a manometer attached, as shown in Fig, P1.52. What is the absolute pressure in pip...
Fundamentals Of Thermodynamics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 34. Four 10 mH inductors are in series. The total inductance is ( a) 40,000 μΗ (b) 40 mH (c) 30 H (d) none of abovearrow_forwardDefine Resistance Proportional to Velocity ?arrow_forwardA circuit contains two un-equal resistances in series Select one: O A. larger potential develops in smaller resistance O B. current is same in both large current flows in larger resistor OD. Potential difference across each is samearrow_forward
- In the network shown, Find the current I and the power supplied by the voltage source, for V = 6 V. + v(* ` 20 k2 Select one: a. I = 0.45 mA, P = - 4.05 mW b. I = 0.2 mA, P = - 0.8 mW c. I = 0.3 mA, P = - 1.8 mW %3D d. I = 0.4 mA, P = - 3.2 mW e. I = 0.6 mA, P = - 7.2 mWarrow_forwardFind the value of the currents I1 and 12. 100 ohm 5V 5V 100 ohm 12 O a. 1=-0.3A, 12=-0.1A O b. 11=0.3A, 12=0.1A Oc. 11=0.05A, 12=0.1A O d. 11=0.1A, 12=0.2Aarrow_forwardTime constant of thermocouple is 5 milliseconds. An engineer measures the temperature of water and sees that the temperature is less than the real temperature of the boiling water (100 C). How long does the engineer need to wait at least to see the 98 C? none of the above 20 milliseconds 10 milliseconds 15 milliseconds not sufficient information 17 millisecondsarrow_forward
- In a given DC motor, the output power is 45 HP, and the copper losses are 2.005 KW. If the rotational losses is one tenth of the output power, find the converted power and the efficiency of the motor. Select one: O a. None O b. Pcony = 33.57 KW and % efficiency = 89.2 % %3D O C. Pcony = 39 KW and % efficiency = 75.8 % O d. Peony = 36.927 KW and % efficiency = 86.2 %. !! n dunlay I AP-wound armature whicharrow_forward2.1) Give the reason for the following statements: 1) Flow reversal can easily be detected by magnetic flowmeters. 2) Using a Venturi flow sensor makes the measurement error due to pressure loading is much lower. 3) For the measurement systems, the signal conditioning element is an important one. 4) Null-type AC Bridge can not be used for measuring the inductive impedance.arrow_forwardTime constant of thermocouple is 3 milliseconds. An engineer measures the temperature of water and sees that the temperature is less than the real temperature of the boiling water (100 C). How long does the engineer need to wait at least to see the 95 C? 8 milliseconds 5 milliseconds 3 milliseconds none of the given 9 milliseconds not sufficient informationarrow_forward
- Q1. Long-shunt generator delivers a load current of 30 A at 220 V. It has armature and shunt field resistances of 0.050, 2000 respectively: A- calculate the generated emf, the copper loss in armature, shunt field loss and the total copper loss. B-if the iron and friction loss is 1000W. Calculate the electrical efficiency, mechanical efficiency, commertial efficiency and maximum efficiency. (Armature reaction may be neglected) Q2. A 220V, 4-pole, lap-connected, shunt motor with 800 conductors in armature slots. The armature and shunt field resistance are 0.62 and 2200 respectively. The motor runs to supply load with 8000W and draw current (50amps) from the mains. The flux per pole is 25mWb A- Calculate the gross torque developed by the armature, the shaft torque (useful), and the lost torque. B- Calculate the gross power developed by the armature, the iron and friction lost power, mechanical efficiency, electrical efficiency, and the overall efficiency. Armature reaction may be…arrow_forwardAn inductor has an inductance of 0.025 H and a wire resistance of 3 Ω. How long will it take the current to reach its full Ohm’s law value?arrow_forwardAn electric kettle is required to raise the temperature of 2 kg of water from 20ºC to 100ºC in 15 minutes. Calculate the resistance of the heating element if the kettle is to be used on a 240 volts supply. Assume the efficiency of the kettle to be 80%.a.72 ohmsc.83 ohms b.62 ohmsd.93 ohmsarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license