Which of the following is NOT true about constant weighing in the experiment? Constant weight is achieved when two consecutive measured weights agree within plus or minus 0.3 mg. It involves a cycle of heating, cooling, and weighing. A proportionality constant will be multiplied to the measured weight to account for loss of water. A desiccator is used to avoid moisture to be absorbed by the sample.

Which of the following is NOT true about constant weighing in the experiment? Constant weight is achieved when two consecutive measured weights agree within plus or minus 0.3 mg. It involves a cycle of heating, cooling, and weighing. A proportionality constant will be multiplied to the measured weight to account for loss of water. A desiccator is used to avoid moisture to be absorbed by the sample.

Chemistry & Chemical Reactivity

10th Edition

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter11: Intermolecular Forces And Liquids

Section11.6: Properties Of Liquids

Problem 1.2ACP

See similar textbooks

Similar questions

A sample was placed on a chromatography column. Methylene chloride was used as the eluting solvent. No separation of the components in the sample was observed. What must have been happening during this experiment? How would you change the experiment to overcome this problem?
You are trying to determine average experimental value with relative uncertainty for the volume of water measured in a 100 mL volumetric pipet with 0.08 mL precision. You follow the procedure below: 1. Weigh a 200 ml flask with a stopper on the analytical balance. Add 100 mL of distilled water measured carefully with a volumetric pipet and re- weight the flask and stopper with the water. 2. Empty the water from the flask and repeat the above procedure two more times for a total of three measurements for the pipet. You collect the following data in your lab notebook: In Lab Data Analytic Balance: Max weight 400 0.0007 g Volumetric Pipet: 100±0.08 ml Density water 1.000 g/ml Trial 1 2 3 Measured Volume (ml) 100.00 100.00 100.00 What is the average percent error in the volumes measured by the pipet? Notes: Canvas will not accept units, so please just input your value-with the correct sig fig Type your answer... Measured Mass (g) 98.1411 98.2413 98.9825
Which of the following is NOT true about constant weighing in the experiment? A A proportionality constant will be multiplied to the measured weight to account for loss of water. B A desiccator is used to avoid moisture to be absorbed by the sample. Constant weight is achieved when two consecutive measured weights agree within plus or minus 0.3 mg. It involves a cycle of heating, cooling, and weighing.
What are the differences between systematic and random errors and how do they effect accuracy and precision? In what circumstances would you use standard addition (versus a normal calibration curve) to determine the amount of an analyte in a sample? A urine sample, containing analyte Z is analysed by the standard addition method where 5 mL of the original sample was mixed with increasing amounts of a Z standard and each solution diluted to a volume of 50 mL prior to analysis. A plot of the final concentration of the standard in each of the 50 mL samples (x axis) versus The measured signal from the analysis of each 50 mL sample (on y axis) produced a straight line with the general equation: y = 44.72x + 4.06 what was the final concentration of Z in the 50 mL standard addition sample? what was the initial concentration of Z in the original urine sample?
Which of the following is NOT true about constant weighing in the experiment? It involves a cycle of heating, cooling, and weighing. A desiccator is used to avoid moisture to В be absorbed by the sample. A proportionality constant will be c) multiplied to the measured weight to account for loss of water. Constant weight is achieved when two D) consecutive measured weights agree within plus or minus 0.3 mg.
What are the types of gravimetric methods? Give an examples where each method is used in an analysis. What is particulate gravimetry? When do we use this technique?
Consider the following SAS data and formula. Volume of sample at $1%: 50.2 ml 51% = 55% 52% = 70% Volume of SAS = [(volume of sample at S1%) (S2% - S1%)] / 100 [(1-(S2% / 100)] Calculate the volume of SAS needed for this experiment given this information.
PAPER CROMATOGRAPHY • Define chromatography • Demonstrate an understanding of the process of chromatography • Describe the steps involved in a chromatography investigation Explanation Coloured inks are often made up of several different inks. Each colour of ink will get carried a different distance by the water, allowing you to see all of the different inks. Try this with different colours to see what actually goes into a colour. This technique is called chromatography and can be used in chemistry to find out what is in an unknown mixture. II. Materials .Felt tip pens (non-washable) . Kitchen roll .A bowl or cup . Water • Scissors III. Health and safety • Make sure that you thoroughly clean any equipment after the experiment before using for food IV. Procedure Method 1 1. Take a sheet of kitchen roll and draw a simple picture with a non-washable felt tip pen. 2. Place the sheet over an empty bowl. This is to keep the paper from getting too wet. 3. Carefully add a few drops of water…
1a. Throughout the experiment, what are some possible sources of error that could have led to someone recovering a significantly smaller amount of table salt (NaCI) than was originally present in the sample mixture. 16. What are some possible sources of error that could have led to someone to appear to have recovered a significantly larger amount of sand (SiO2) than was originally present in the sample mixture.
The following volumes of 0.000300 M SCN are diluted to 15.00 mL. Determine the concentration of SCN in each sample after dilution. These values will be used during the experiment. To enter exponential values, use the format 1.0e-5. Sample 0.000300 M SCN (mL) [SCN'] (M) 1 1.50 3.50 7.00 4 10.00 3.
Analysis of a chromatogram of a mixture containing 0.0124 M analyte and 0.0448 M standard found that the peak area from the analyte was 324 and that the peak area from the standard was 258. In another experiment, a solution containing an unknown concentration of analyte and 0.0381 M standard was analyzed. The peak area of the analyte was 231, and the peak area of the standard was 197. What is the molar concentration of the unknown?
Suppose a normally distributed set of data with 8900 observations has a mean of 123 and a standard deviation of 16. Use the 68-95-99.7 Rule to determine the number of observations in the data set expected to be above a value of 107. Round your answer to the nearest whole value. Hint: This problem is asking for how many observations not the percent. Answer Tip: Don't round any probabilities or percentages in your calculations. Keep all decimal places and round at the END of the problem.