Tube with 100 mm long and 20 mm diameter. If the axial load is 30OON is.applied to it. Determine the stress and strain if change in length AL=0.5mm3000 Nd=20 mmL=100 mm3000 N

Answered: Image /qna-images/answer/3f82d53e-c874-4e80-a37d-de83d64c97f4.jpg

Answered: Tube with 100 mm long and 20 mm…

Tube with 100 mm long and 20 mm diameter. If the axial load is 30or .applied to it. Determine the stress and strain if change in length AL=0.5r 3000 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A hollow iron pipe with outside diameter of 240 mm is used as a column to carry a load of 80 kN.…

Q: Determine pressure in [kPa] in the cylindrical pressure vessel shown, if the measured hoop strain is…

A: Given, εhoop=500×10-6E=70 GPa=70×109 Paμ=0.33Ri=400 mm=400×10-3 mmt=6 mm=6×10-3 mm Internal diameter…

Q: The state of stress at the point can also be represented in termsof the maximum in-plane shear…

A: False, The state of stress at the point cannot be represented in terms of the maximum in-plane shear…

Q: Q/ If the cross section of the femur can be approximated as a circular tube, determine the state of…

A: Consider the diagram shown below for the femur. At point A, there will be a shear stress because of…

Q: determine the developed stresses, the changes in length, and the changes in diameter for QI: The bar…

Q: Determine strain if change in length 0.34 mm and initial length 250 mm

A: Given:∆L=0.34 mmL=250 mm

Q: The bar shown is subjected to a tensile load of 160KN. If the stress in the middle portion is…

Q: If the allowable tensile stress for the bar is (o,) allow = 21 ksi, and the allowable shear stress…

Q: The pole BC is supported by a pin C and by the steel wire AB. A horizontal force of 30 kN is acted…

A: Given data, Horizontal force at E, FE = 30 KN Ultimate shear stress of the pin, ?ut = 100 MPa…

Q: The bar has a 100 mm by 15 mm rectangular cross section. The allowable normal and shear stresses on…

Q: Q 2: A cantilever beam has the profile shown so that it will provide sufficient clearances for large…

A: GivenAxial load P=115.33kNT section cantilever beam as shown below

Q: The grains of wood in the board make an angle of 20° with the horizontal as shown. Using Mohr's…

A: Given that:P=280 Nb=25 mmd=60 mmθ=20ο

Q: H.W.8: Calculate the stresses, if the strains displayed on the lement have been applied. Use all…

A: To obtain the required stresses, we must first determine the principal strains in the element using…

Q: The pipe assembly shown is subjected to a force F= 600 N. The pipe has an inner diameter of 20 mm…

A: Consider the Free Body Diagram: Torque,T=600*0.2 =120 N.mTorque acting on part BC,TBC=120 N.mTorque…

Q: A nylon thread is subjected to a 3.2-lb tension force. It is given that E= 0.5 x 106 psi and the…

A: Given data:

Q: Q 2: A cantilever beam has the profile shown so that it will provide sufficient clearances for large…

A: Given: The load is 115.33 kN. The T cross section is shown below:

Q: The rigid beam ABC is supported by pin A and wires BD and CE. If the load P on the beam causes the…

Q: 5.0 in. 3.0 in. The 1.4-kip load P is supported by two wooden members of uniform cross section that…

A: Given load P=1.4 kip Cross section A=5×3 in.2

Q: Determine the lateral strain, in mm/mm, in the 5 mm diameter aluminum T6 rod when P = 8 kN. Use L =…

A: Given:-P=8 kNL=400 mmE=70 GPa=70×109 Pav=0.35To find:-Lateral strain

Q: if the rod is subjected to a tensile load P = 6 kN, and has a diameter of 44 mm. if the modulus of…

Q: If the copper in no. 2 is changed into steel with the same dimensions and with a modulus of…

Q: The grains of wood in the board make an angle of 20 with the horizontal as shown. Using Mohr's…

Q: Initially, gaps between the A-36 steel plate and the rigid constraint are as shown. Determine the…

A: Given Data: The increase in the stress is ∆T=100°F. Increase in length in x direction is δx=0.0025…

Q: The spherical pressure vessel has an inner diameter of 2 m and a thickness of 10 mm. A strain gage…

A: Given Data: Inner diameter of sphere is di = 2 m. Thickness of sphere is t= 10 mm. Length of strain…

Q: 1) Determine the tensile stress developed in member AB due to a load of P = 500# at D. The member AB…

A: The given figure can assumed to be a truss because it is supporting a load. Thus, a structure made…

Q: a 300 mm 300 mm а F Find the maximum F that can be applied to the lever, if the material has a yield…

Q: 1. Neglecting the weight of the steel wire, determine its required diameter if it is 30 ft long,…

A: Given data, L= 30 ft = 360 in Elongation ∆L= 0.4 in P= 500 lb E= 49*10⁶ psi Stress limit s=…

Q: The rods A and B having a tensile stress of 400 N/mm², determine the diameter so that they can…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: Tube with 100 mm long and 20 mm diameter. If the axial load is 300ON is applied to it. Determine the…

Q: The lap joint is fastened with four 0.75-in.-diameter rivets. The working stress is 15.77 ksi for…

Q: Determine the average normal and shear stresses at a cross section (a-a) for e-65. The member has a…

A: Draw the F.B.D of the given cut section of the element.

Q: The cross-sectional area of the bar ABCD is 600 mm². Determine the maximum normal stress in the bar?

A: Assume that the bar ABCD is The load acting on the bar is P The maximum normal stress then act on…

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given: P=64 kips d=0.75 in

Q: For the bar in the way the loading status is seen determine the strain energy on the rod so that the…

A: The maximum allowable stress will be a constraint for the hollow shaft because, for the same outer…

Q: Q3: The yoke-and-rod connection is subjected to a tensile force of 15 kN. Determine the average…

A: Dear student, According to the guidelines I am allowed to answer only one…

Q: The grains of wood in the board make an angle of 20° with the horizontal as shown. Determine the…

A: Given data: Axial load acting on the wooden block, P = 250 N. Width of the wooden block, b = 25 mm.…

Q: Find the stress in the rod having a diameter of 20 mm, subjected to 10 kN force. If the material of…

Q: The steel end-cap is fitted into grooves cut in the timber post. The working stresses for the post…

Q: If the load P= 60N on the beam causes the end C to be displaced 10 mm downward: a) determine the…

A: Given-Data:- P=60N Assuming the length BD=4m To-Find:- a) Normal Strain in BD b) Shear Stress in…

Q: The truss members below have the shown length and they all have a solid diameter of 50 mm 1.…

A: given data diameter(d)=50mmlets take reaction force at A&F=RA &Rf area (a)=π4…

Q: Determine the average normal strains in the two wires in Figure if the ringat A moves to A′.

Q: Determine the average normal and shear stresses at a cross section (a-a) for e= 65". The member has…

Q: With the same given, if the members have a square cross-section with a diagonal of 11.31 cm and…

A: In the question, the applied magnitude of force is not given, thus it is not possible to calculate…

Q: The head H is connected to the cylinder of a compressor using six 316-in. diameter steel bolts. If…

A: Given Data σy=40ksiEst=29000 ksi Find out the cross-sectional area A=πd24=π43162=0.027597 in2

Q: (a) the normal stresses in the steel plates (1) and the oak block (2). (b) the shortening of the…

Q: circle for sx = sy = txy = 2 kPa. On the circle, label the axes and the principal stresses and their…

Q: If the allowable tensile stress for the bar is (ot)allow = 22.6 ksi, and the allowable shear stress…

Q: The modulus of elasticity for the steel cable is 25 (10)^6 psi. Determine the average stress in the…

A: Average stress is stress which produces due to pressure or forces which does not exceed the elastic…

Question

Tube with 100 mm long and 20 mm diameter. If the axial load is 30OON is
.applied to it. Determine the stress and strain if change in length AL=0.5mm
3000 N
d=20 mm
L=100 mm
3000 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The vertical steel rod has a constant diameter of 32 mm and a length of 400 mm. is hanged from a rigid fixing. A mass is gently placed onto a collar which is attached to the lower end of the rod. The strain energy stored in the steel is 0.400 x 10-³. If Esteet = 209 GPa, 1.1 Determine the gradually applied load and magnitude of the mass. 1.2 Calculate the maximum stress in the rod when gradually applied. 1.3 Determine the magnitude of the mass when the mass is suddenly applied. 1.4 Calculate the extension of the rod when suddenly applied.
Question 1 The vertical steel rod has a constant diameter of 32 mm and a length of 400 mm. is hanged from a rigid fixing. A mass is gently placed onto a collar which is attached to the lower end of the rod. The strain energy stored in the steel is 0.400 × 10-3. If Esteel = 209 GPa, 1.1 Determine the gradually applied load and magnitude of the mass. 1.2 Calculate the maximum stress in the rod when gradually applied. 1.3 Determine the magnitude of the mass when the mass is suddenly applied. 1.4 Calculate the extension of the rod when suddenly applied.
Find the initial length of rod if strain value is 0.0003 and change in length value 0.3 mm
Determine strain if change in length 0.34 mm and initial length 250 mm
983. The strain components at a given point are , = -800 X 10-6, €y = and Yxy 200 X 10 , 0.30, find the stress components -800 X 10-6. If E = 200 GPa and v = on the face whose normal is at +20° from the x axis. Ans. o = -105 MPa; 7 = -96.6 MPa
Question 1A rod with a diameter of 30 mm and a length of 600 mm is subjected to an axial force of 60 kN which causes an elongation of 0.30 mm. Determine the stress in the rod, the strain, and the modulus of elasticity of the material.
Determine the average normal strains in the two wires in Figure if the ringat A moves to A′.
The strain at a point is 780x10-6 in the x, 400x10-5 in the y and -500x10-6 in the z direction. Determine the stress state if the Young's modulus is 10,640 ksi and v = 0.33.
Determine the change in length, width and thickness of steel bar which is 4m long, 30mm wide and 20mm thick and is subjected to an axial pull of 30 kN in the direction of length. Take E = 200 GPa and poison's ratio of 0.3. Also determine the volumetric strain and change in volume.
= 2-Consider a 45° off-axis tensile test coupon. Three strain gages attached as shown below are reading el 0.00647, 2= -0.00324, and 3 = 0.008095 at stress level of ox=100 MPa. Determine the off-axis modulus of elasticity Ex the off-axis major Poisson's ratio vxy and coefficient of mutual influence of the second kind nxy,x 2 √²-01-² y 45° €2 0₂
7. Determine the stress developed in the Tensional Cord given that the cable's diameter is 0.6 inches and the bar weigh 6kips. Figure P-106 3 m 5 m 5 m E
Shown is the stress-strain curve developed from the tension test of a metal alloy bar. The specimen used to develop the stress-strain curve has a round cross-section with a diameter of d = 7 mm and a gauge length of L = 370 mm. Determine the load that must be applied to the specimen to stress the specimen to it's 0.2% offset yield. Express your answer in kN to the nearest whole kN. Your written solution must also include the length of the specimen when stressed to the 0.2% offset yield stress. σ (MPa) 700 600 500 400 300 200 100 0 0.02 0.04 0.06 0.08 0.10 0.002 0.004 0.006 0.008 0.010 € (mm/mm) P d