If the allowable tensile stress for the bar is (o,) allow = 21 ksi, and the allowable shear stress for the pin is Tallow = 12 ksi, determine the diameter of the pin so that the load P will be a maximum. What is this load? Assume the hole in the bar has the same diameter d as the pin. Take i = in. and w = 2 in.

If the allowable tensile stress for the bar is (o,) allow = 21 ksi, and the allowable shear stress for the pin is Tallow = 12 ksi, determine the diameter of the pin so that the load P will be a maximum. What is this load? Assume the hole in the bar has the same diameter d as the pin. Take i = in. and w = 2 in.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.10P: Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa

See similar textbooks

Similar questions

If the allowable tensile stress for the bar is 1st2allow = 21 ksi, and the allowable shear stress for the pin is tallow = 12 ksi, determine the diameter of the pin so that the load P will be a maximum. What is this load? Assumethe hole in the bar has the same diameter d as the pin. Take t = 1 4 in. and w = 2 in.
3 m Load D 2 m+ 3 m The member AC is made from an aluminium alloy and has a rectangular cross section of 100mm x 10mm. Calculate the stress in member AC if a load of 57.4 kN is applied at point D.
The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap D= 4 mm between the lower end of the left rod and its pin support at C. Compute the stress in the left rod after its lower end is attached to the support. The cross-sectional areas are 300 mm2 for rod AC and 250 mm2 for rod BD. Use E= 200 GPa for steel. lo/0 0.75 m 1.5m 2 m ANSWER: MPa
The lap joint shown is fastened by 4 rivets of ¾ in. diameter. Find the maximum load P that can be applied if the working stress are 14000 psi for shear in the rivet and 18000 psi for bearing in the plate. Assume that the applied load is distributed evenly in the 4 rivets. The plate is 7/8 in. thick and 4 in wide.
the right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of the load P that can be applied if the shear stress in the pin is limited to 20000 psi? the 3/4 in diameter pin is in double shear
I Reviev Part A If the allowable tensile stress for the bar is (0t)allow = 22.6 ksi, and the allowable shear stress for the pin is Tallow = 12.2 ksi. Assume the hole in the bar has the same diameter d as the pin. Take t = 1/4 in. and w = 2 in. (Figure 1) Determine the diameter of the pin so that the load P will be a maximum. Express your answer to three significant figures and include appropriate units. HÀ ? d = Value Units Submit Request Answer Part B What is this maximum value for P? Express your answer to three significant figures and include appropriate units. Figure 1 of 1 HA ? w/2 P = Value Units w/2 Submit Request Answer
find the allowable safe load p if the stresses in the bar are the following : ab=50ksi bc=60 ksi cd= 70 ksi
The 20-mm-diameter bolt fastens two wooden planks together. The nut is tightened until the tensile stress in the bolt is 150 MPa. Find the smallest safe diameter d of the washers if the working bearing stress for wood is 13 MPa. 20 mm
The lap joint is fastened with four 3/4-in. diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets.
A metal bar is made out of A-36 steel and has a diameter d 20mm with the end at A fixed to the wall. There is are balanced axial loads at B of P₁ = 50 kN and a point load at C of P2 = 40 kN. The distance from A to B is L₁ = 600 mm and the distance from B to C is L2 400 mm. Calculate the displacement of point C relative to point A. The modulus of elasticity for steel is E = 200 GPa A d B The displacement at C is 8 = P₁ 1 Р1 с BY NO SA 2021 Cathy Zupke mm P2
@2 The support consists of solid brass post surrounded by a steel tube. Before the load is applied, the gap between these two parts is | mm. Given the dimensions shown in the figure, determine the greatest axial load that can be applied 0 the rigid cap A if the maximum allowable stress in brass is (Guiin)se = 150 MPa and the maximum allowable stress in steel is (Gun ) = 200 MPa. E, = 200 GPa and Ey,= 100GPa.
The lap joint is fastened with four 3/5 in-diameter rivets. The allowable normal stress in the plates is 30 ksi, allowable shearing stress is 24 ksi for the rivets and 28 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. Include the necessary FBDs showing the involved internal forces in the exploratory sections. Your solutions are invalidated without the required FBDs.