Answered: The Volume of NaOH (0.01N) when use…

The Volume of NaOH (0.01N) when use ph.ph indicator is 12.4mL and 3mL when use methyl Orange (M.O) and the Volume of Sample is 30mL, Calculate the Total Acidity as mg (CaCO3)/L. (EW for CaCO3 is 50)

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.18P

See similar textbooks

Related questions

Q: Sanitary Engineering laboratory "jar test " 4. Write the significance of pH in coagulation…

Q: A column 3.00 cm in diameter and 32.6 cm long gives adequate resolution of a 72.4-mg mixture of…

A: Given : diameter = 3.00cm length = 32.6cm mass of mixture = 72.4mg initially dissolved in 0.500mL…

Q: A sample is diluted to perform test 295 ml distilled water are added to 5mL sample to fill 300 ML…

Q: Q/ A wastewater treatment use an activated sludge process for secondary treatment of 10000 m/day for…

A: Inflow Rate (Q) = 10000 m3/dayInitial BOD (S0) = 150 mg/L =150×10-610-3 kgm3 = 0.15 kg/m3Soluble…

Q: A 50 ml sample of industrial wastewater is taken into a silica crucible. The empty weight of the…

A: Given, quantity of sample taken = 50 ml =50x 10-3L empty weight of the crucible =54.352 g dry weight…

Q: Q3) There are suspended solids in produced fluids such as scale deposits, corrosion products, sand…

A: Diatomaceous Earth (DE) Filters: Diatomaceous Earth Filter comprises of diatomaceous earth which…

Q: 100-mL water sample is mixed with 200 mL of deionized water for BOD analysis. The DO of the mixture…

Q: A untreated waste water enters a stream as shown in figure. The concentration of sodium in the…

A: Given data, The concentration of sodium =15 mg/l flow rate=20 m3 /sec The concentration of sodium in…

Q: 8. The BODS of a waste sample was found to be 160 mg/L. The initial oxygen concentration of the…

Q: Derive the equation for effluent tracer concentration from a CFSTR. Assume a step-input tracer test.…

Q: A water contains a suspended solids concentration of 10.30 mg · L−1. Coagulation reduces this to 1.0…

Q: Q-3: A river before its entry into a town had a discharge of 100 1/sec and 20 mg/L as the…

Q: Jar testing was performed using alum on a raw drinking water source that contained initial turbidity…

Q: 1. The particle settling velocity in a fluid–particle suspension: (a) increases with increasing…

A: Following are required explanations :

Q: The BOD, of a waste sample, was found to be 40.0 mg/L. The initial oxygen concentration of the BOD…

Q: 5. A water sample has been analyzed. Upon titration with EDTA, the following results were gathered.…

A: Given, Volume of water sample = 10 ml Volume of CaCO3 = 5 ml

Q: Bottle No. Volume of Initial PH Final PH Initial turbidity Final turbidity coagulant stock need (ml)…

A: Bottle 1 & 2 PH = 5.6 PH = -logH+10 5.6 = -logH+10 H+= 10-5.6 mol/ml concentration(mg/ml) =…

Q: In wastewater treatment the digestion of sludge produces a useful gas (carbon dioxide and methane),…

A: Discharge is the main quantity in any sector that is used to transfer fluid from one place to…

Q: MPN of effluent is 10/100 ml and it reduces to 102/100 ml after chlorination. Find percentage…

A: Given: Initial MPN value = 106/100 ml Final MPN value = 102/100 ml

Q: A standard BOD test is run using seeded dilution water. The blank bottle containing the seeded…

Q: a) How can you determine chloride content in a waste water sample? Subject: environmental…

A: Chloride, within the style of chloride (Cl–) particle, is one in every of the main inorganic anions…

Q: A water sample was tested for water hardness. A 50.00 mL sample, prepared and buffered to pH 10,…

A: The given data is shown below:

Q: Suppose the estimated BOD of an influent sample is expected to be 150 mg/L and the dissolved oxygen…

A: Calculating BOD of raw sewage: Because we have given a condition:

Q: Table 1 shows the result of the sieve analysis for the material of asphalt concrete (AC) mixture.…

A: To Determine Whether the sample sieved is fulfilling the requirement according to the given…

Q: A tank with a capacity of 1500 gallons originally contains 1000 gals of fresh water. The first pipe…

A: Given: capacity of tank 1500 galon having 1000 galon fresh water first pipe 1/2 lb Of gallon is…

Q: From the table shows a summary of a liquid limit and plastic limit test. Compute the natural water…

Q: A BOD test is run using 100mL of treated wastewater. The initial DO of the mixture after diluting…

A: Solution: Given data Volume of Sample= 100 mL Initial DO of sample=DOi=9 mg/L Final DO of sample…

Q: Determine the relationship between the observed/apparent value (EX) VERSUS that of the true value…

A: Given data- observed/apparent value= EXtrue value ETiron-phenanthroline method- ppm Fe in a water…

Q: 10-1. In a 5-day BOD test, the initial DO concentration was 7.8 mg/L and the final concentration was…

Q: 1- Explain the procedure to find the total solid and what's the unit for it? 2- In total dissolved…

A: Procedure to find the total solids and it's unit.

Q: Calculate the BOD concentration based on the data below. DOinitial (mg/L) 7 DO final (mg/L 3.5…

A: step 1-

Q: hese chemicals would you use to calculate hardness? (b) All aqueous solutions must ge neutrality.…

A: hardness of water =?

Q: MPN of effluent is 106/100 ml and it reduces to 102/100 ml after chlorination. Find percentage…

A: Given: Initial MPN value = 106/100 ml Final MPN value = 102/100 ml

Q: In standardization, 10.00 mL of Naz C2 04 solution required 39.17 mL of KMN04. Find the molarity of…

A: Standardization Process: Assuming that 0.3562 g of Na2C2O4 is dissolved in 250 mL of water to make a…

Q: t more than 7 mg/L of soluble BOD in the effluent. The mixed liquor has a concentration of 3000 mg/L…

Q: Retardation factor

A: Given Data : bulk density = 2.8 Koc = 3.11 porosity = 0.2 Required- to find Retardation factor

Q: An industrial waste with a flowrate of 110 L/min contains 40 mg/L of zinc. Calculate: 1.) the pH…

A: Given Flowrate of industrial waste = 110L/min Molarity of Zn = 40mg/l To find 1. pH to maintain…

Q: 10.The process by which a removal of suspended solids from wastewater through the addition of…

A: step 1-

Q: The waste water is flowing at a rate of 0.2 m³/s in a settling tank. The specific gravity of…

A: Given that: Flow rate of wastewater, Q=0.2m3/sSpecific Gravity of particles,…

Q: The following dissolved-oxygen values were found after 5days of incubation in 310-mL BOD bottles:…

A: Biochemical Oxygen Demand or BOD is defined as the oxygen required to oxidize the biodegradable…

Q: Which type of Acidity is fit for drinking water

A: The water or any liquid can be classified as acid or base (alkaline). This can be determined using…

Q: For testing Total acidity, the indicator used is

A: The water or any liquid can be classified as acid or base (alkaline). This can be determined using…

Q: Identify, from the list, below the primary purpose of each of the following wastewater treatment…

A: And 1-C Grit chamber is used to remove descretd particles such as coffee grinds, sand,glass…

Q: Wet coal is dried in a continuous rotary dryer that operates at atmospheric pressure. The chips with…

A: Molecular weight: Molecular weight is the weight of the given substance or molecule. The molecular…

Q: In determination of Acidity experiment, If the volume of 0.02N NaOH when use Methyl Orange (M.O) is…

A: Given data: Normality of NaOH = 0.02 N Volume of methyl orange (V1) = 0.8 mL Volume of…

Q: Waste activated sludge contains 1% dry solids that are 80% volatile. Determine: a. The specific…

A: Specific gravity is the ratio of the density of a substance to the density of given reference…

Q: In determination of Hardness, If the volume of EDTA (0.02N) is 17.8 mL, the Volume of sample is 20…

A: Given: The volume of sample is 20 ml. The EW of caco3 is 50. Calculation: The formula to calculate…

Q: Compute the liquid limit. b. Compute the plastic limit. c. Compute the natural water content. d.…

A: (a) The liquid limit is to be determined.

Concept explainers

Integrated Solid Waste Management

Integrated Solid Waste Management (ISWM) is a thorough waste suppression, compost, removal and recycling Program. An effective ISWM system considers how to suppress, manage and recycle solid waste in a manner that is most efficiently to protect human health and the surrounding. ISWM system requires evaluation of public wants and demands and then selecting and merging the most effective waste management activities for the proposed demands. The main ISWM activities for solid waste management are Waste prevention, Recycling and Composting, and Combustion and Removal and waste collection in a properly planned, constructed, managed and mitigated landfill areas. Each of these requires careful designing, financing, accumulation, and delivery of activities.

Question

The Volume of NaOH (0.01N) when use ph.ph indicator is 12.4mL and 3mL when use
methyl Orange (M.O) and the Volume of Sample is 30mL, Calculate the Total Acidity as
mg (CaCO3)/L. (EW for CaCO3 is 50)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Which of the following statements is not true about acids? A weak acid is not dangerous and may be handled without proper personal protective equipment. After prolonged exposure to acids, a person may experience throat irritation. When handling acids, one must not wear contact lenses. Acids must never mix with solvents because this will result to an explosion and fire.
Chose the correct answer 1- The Unit measurement of suspended solids is ...A- kg 2- The Unit measurement of Turbidity is A- °C is B-m B-NTU C- mg/L C-K 3- The Unit measurement of pH www A-mg/L 4- The Unit measurement of alkalinity is .. 5-Non toxic metals includes 6-Dissolved materials size is lees than A- 10 mm D- none of above D- none of above D- none of above B- p.p.m C- g/m³ D- none of above A- m/sec B- m³/sec C- mg/L A-Chromium B- Mercury C- Calcium D- none of above B- 106, C-108 mm D- none of above mm 7- Public standards of Hardness in drinking water is A-500 mg/L B-50 mg/L C-100 mg/L D- none of above 8- Alkalinity species includes are A-HCO3 B-CO3 C- OH D-All of above ... 9- Dental cavities in children can prevented when Drinking water has Fluoride concentration of A- 0.1 mg/L B- 1 mg/L C- 10 mg/L D- none of above 10- Toxic metals are metals that harmful to humans even when exists in concentration of .. A- Small B-Large C-zero D- none of above
You made an error and changed the concentration of your NaOH from 0.100M to 1.00M for the potentiometric titration of acetic acid. Beyond this, you followed the rest of the procedure properly. Your acetic acid's buffer capacity will (increase, decrease, not be affected) because
Communicate the steps during the titration of a weak base with a strong acid. Explain the major concepts of titration and how to calculate the pH at any point on the curve.(Explain as if someone is learning the topic for the first time)
(a) (ii) Following chemical species were reported for water sample from a well. Concentration (milli equivalent)/L 15 15 05 30 12 18 8.8 Species Chloride (CL) Sulphate (SO2-) Carbonate (CO2) Bicarbonte (HCO3) Calcium (Ca²+) Magnesium (Mg2+) pH Find (i) The total hardness (in mg/L) as CaCO3 (ii) Alkalinity present in the water (in mg/L) as CaCO3.
In the process of biological treatment of wastewater, the concentration of dissolved oxygen (DO) is determined by several physical and biological phenomena, such as hydraulic transport of oxygen in and out of the aeration tank, transport of mass of oxygen in the gas phase into dissolved oxygen and utilization of oxygen due to growth and decay of cells. Consider the perfect mix aeration tank, where y is the dissolved oxygen concentration, and yi is the dissolved oxygen concentration. in the influent, F is the influent wastewater flow and V is the volume of the aeration tank and u is the flow of air into the aeration tank. Develop a control system that use feedback control to control DO concentration.
Please choose the correct answer for each question: 1. Activity of a gas in equilibrium with solution is ______? A. its partial pressure; B.1.0; C. its molar concentration; D. 0.0 2. During a sorption procedure, the substance transferred from the gas or liquid phase to the solid phase is called ______ A. sorbent; B. sorbate; C. partition; D. none of the above 3. When a chemical has a lower KOW, it is more ______ A. hydrophobic; B. hydrophilic; C. more absorbable; D. less absorbable 4. _____ occurs on the adsorbent surface A. Adsorption; B. Sorption; C. Absorption; D. Adsorption and absorption 5. _____ addresses the change in the amount of a substance of interest with time. A. The equilibrium approach; B. The kinetic approach; C. Henry’s Law; D. Freudlich isotherm equation
Available chlorine in bleaching powder solution is 0.5mg/ml. To obtain a chlorine dose of 0.1 mg/1 in a 300 ml water sample, the amount of bleaching powder solution to be added is ml.
In determination of Acidity experiment, If the volume of 0.02N NaOH when use Methyl Orange (M.O) is 0.8 mL and 7.8 mL when use Phenolphthalein (Ph.Ph), the volume of sample is 25mL and the EW for CaCO3 is 50. The Mineral Acidity as mg (CaCO3)/L is
The following test results (Table Ql-2) were obtained from a raw water sample. All of the tests were performed using a sample volume of 50 mL. Table Q1-2 Weight (g) Mass of residue after drying at 105 ỏC Mass of residue after ignition at 550 ¿C Mass of residue on Whatman GF/C filter paper after drying at 0.7148 0.3818 0.3571 105 'C Mass of residue on Whatman GF/C filter paper after ignition at 550 'C 0.1418 Calculate the concentration (mg/L) of : (i) total solids. (ii) total volatile solids. (iii) total suspended solids. (iv) total dissolved solids.
3. Some industrial spent catalyst was tested as adsorbent material in a batch experiment. The data are reproduced in the following table. Determine the Final Conc., Ce (mg/L) 14.88 9.55 1.89 0.58 0.44 0.61 0.36 Uptake, q (mg/g) 8.80 8.41 7.33 6.15 5.68 4.92 3.79 a. Determine the coefficients for these data assuming a Freundlich isotherm applies. b. Determine the coefficients for these data assuming a Langmuir isotherm applies. c. Which isotherm model provides a better fit to the data? Explain.
3. Table below shows the concentration of dissolve oxygen for a BOD test, diluted by 100. Time (days) Diluted sample DO (mg/L) 7.95 1 3.75 2 3.45 2.75 2.15 1.8 i. Determine BOD5 Given the deoxygenation rate coefficient of 0.15 day-1, determine the ultimate BOD ii. iii. Based on answer from (i), identify class of the water sample based on INWQS guideline and propose suitable usage the water.