The lap joint carries an P axial load of P - 50 kN. It is connected by 3-18 mm 150 mm 20 mm 20 mm dia. rivets. 38. What is the bearing stress between a plate and a rivet? 39. What is the shear stress in rivet? 40. What is the maximum average tensile stress in each plate?

The lap joint carries an P axial load of P - 50 kN. It is connected by 3-18 mm 150 mm 20 mm 20 mm dia. rivets. 38. What is the bearing stress between a plate and a rivet? 39. What is the shear stress in rivet? 40. What is the maximum average tensile stress in each plate?

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter22: Welding Joint Design And Welding Symbols

Section: Chapter Questions

Problem 4R: Sketch a V-grooved butt joint, and label all of the joint's dimensions.

See similar textbooks

Related questions

Q: Q2: Two plates 10 mm thick are joined with a double riveted lap joint. The pitch of each raw of…

Q: Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint.…

Q: 1.) A long flat steel bar 6 in. wide and 3/8 in. thick has a 2.5 in. diameter circular hole…

Q: The one end of a hollow square bar whose side is 10.17 with thickness is 1.17 under a tensile stress…

Q: 3.3 A steam boiler is to have a 300-mm-diameter hand hole placed on one end. If the maximum internal…

Q: Find the value of P for the two joints shown Take safe working stress of t=103 MPa. Which joint has…

A: Since the load P is passing through the centroid of the figure, so there is only Primary shear…

Q: The rigid bar of negligible weight is pinned at o and attached to two vertical rods. Assuming that…

Q: (Q1) A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axial tensile load of…

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

Q: A flange coupling with bolt circle of 250 mm uses 8 bolts, 25 mm diameter, the torque transmitted is…

A: Given Data The diameter of the bolt circle is D=250 mm. The number of bolts are n=8. The diameter…

Q: An eye bolt carries a tensile load of 20 kN. Find the size of the bolt , if the tensile stress is…

Q: The central plates a in Fig.12 of the text are 9/16 in. thick and 9 in. wide. The diameter of the…

Q: Given a 2meter Wide Flange steel compression member with A=4,513mm2, Ix=86,630,006mm4 and…

Q: The one end of a hollow square bar whose side is 10.68 in with 1.68 in thickness is under a tensile…

Q: 2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main…

Q: The axial load 274 kN applied to the lap joint is distributed equally among the three…

A: Given: P = 274 kN n = 3 d = 26.5 mm w = 135.4 mm t = 29.5 mm

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

Q: 5. A load of 5 kN is to be raised by means of a steel wire. Find the minimum diameter required, if…

A: Given data: F=5 kNσ=100 N/mm2 Need to determine the minimum required diameter of the wire.

Q: 1. A reciprocating steam engine connecting rod is subjected to a maximum load of 65 kN. Find the…

A: Question (1) is Solved here. For Other Question, Please Post this Question.

Q: Consider the bracket shown in Fig-3. If: • F1 = 10 lb @ -90° • a - 2 ft • b = 4 ft C = 1 ft then,…

Q: Calculate the normal stresses (in Pa) at point Bof the bracket caused by the 23010N force. E4.png -…

Q: The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress…

Q: load of 200 KN. If the length of the bar is 2 m and E = 200 GPa. What will be the elongation of the…

Q: A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the…

A: Given A steel bolt Tensile load P=40kNMajor diameter(d1)=6 mmMinor diameter d2=4 mmAverage tensile…

Q: Design the yoke and rod connection as shown on the figure to withstand a load of 14 KN. If the…

Q: The thrust bearing supports a load P = 275KN. Find a. The tensile stress in the rod b. The shearing…

Q: The one end of a hollow square tube whose side is (10+N/100) in with (1+N/100) in thickness is under…

A: Data given - Side a = 10+ 47/100 = 10.47 in Thickness t = 1+47/100 = 1.47 in tensile stress σt =…

Q: ods were stress-free. Determine the load in each rod if W = 51.29 KN. listance into mm. | Figure…

Q: 8000 lb 3000 lb 7000 lb 2000 lb 4' 5' 3' Fig. P-208 and P-209. up (73 208. An aluminum bar having a…

A: To find: The total deformation. Give: The Young's modulus is E=10×106 psi. The cross sectional area…

Q: Q1/ Calculate the forces in all rivets for the rivet group shown. 24KN 600mm 300mm 240mm

A: Given:Applied load on rivets, P=24 kN

Q: igure below are cables ( circular section) supporting a MN kN. Find the axial stress of each. The es…

Q: Question 5 required to raise the load if the yield stress of steel is 300MPA. A lead of 5kN is to be…

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

Q: Wi Wz _F STEM PART 1 TAB TAB STEM TAB TAB PART2 BY NC SA 2014 Michael Swanbom Dimensions: WĄ W2 W3…

A: Stress is the ratio of force and area.

Q: 2. A square aluminum bar should not stretch more than 1.4 mm when it is subjected to a tensile load.…

Q: I- The two plate-shaped parts given below are joined with a rivet. Examine this figure and formulate…

A: Part (1): For this case, total shear force is transmitted through highlighted single red face (as…

Q: Figure shows a roof truss and the detail of the riveted connection at joint B. Using allowable…

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have a square…

A: Calculate tension in AB for moment equilibrium about C T x 6 = 20 x 9.5 T = 31.6666 N

Q: 1. An engine cylinder is 300 mm in diameter and the steam pressure is 0.7 N/mm2. If the cylinder…

Q: Find the smallest and safestd of the link as shown on the figure, if the working stress is equal to…

A: Find the smallest diameter

Q: A metal tube with inside diameter of 100mm is subjected to a tensile lad of 500kN. Find the outside…

A: Inside diameterdi=100 mm di=0.1 m Outside diameter=do Tensile loadP=500…

Q: A horizontal plate has been joined to a vertical to a vertical post using four rivets arranged as…

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

Q: The one end of a hollow square bar whose side is 10.42 in with 1.42 in thickness is under a tensile…

Q: An engine cylinder is 300 mm in diameter and the steam pressure is 0.7 N/mm2. If the cylinder head…

Q: 4. The bar below is subjected to an axial load of P. The safety factor against compressive failure…

Q: Situation 2: The butt connection shows 8- 22 mm diameter A325 bolts spaced as shown. The diameter of…

Q: A cylinder head for steam engine is held by (14) bolts. The effective diameter of the cylinder is…

Q: 2. A bracket, as shown in Fig. 2, carries a load of 10 kN. Find the size of the weld if the…

Q: Find the smallest and safest d of the link as shown on the figure, if the working stress is equal to…

A: Given Working stress, SN = 20 MPa Force, FN = 10 kN Find Diameter, d

Question

The lap joint
carries an
P
axial load of
P - 50 kN. It
is connected
by 3-18 mm
150 mm
20 mm
20 mm
dia. rivets.
38. What is
the bearing stress between a plate and
a rivet?
39.
What is the shear stress in rivet?
40. What is the maximum average tensile
stress in each plate?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two steel plates linked together via a double riveted butt joint is subjected to the load P. Assume that the applied load distributes evenly among the ten identical rivets and neglect friction. a. Draw the FBD of a middle plate and that of a cover plate. Label forces as a function of P. b. Draw the FBD of a rivet. Do all rivets experience the same shear stress? Why or why not? c. How many unique values of the bearing stress can be solved? Enumerate all. d. What is the maximum tensile stress in the middle plate? in the cover plate? Answer in terms of P. Use the following dimensions: diameter of rivets - 10 mm, thickness of cover plates - 15 mm, thickness of middle plates - 25 mm, width of both plates-100 mm. P- P- P -P
The central plates a in Fig.12 of the text are 9/16 in. thick and 9 in. wide. The diameter of the rivets connecting these plates to the outside plates is 1 in. If the allowable unit stress in tension on the net area is 20,000 psi, the safe tensile strength of eith central plate is A. 90,000 lb B. 88,600 lb C. 78,600 lb D. 75,800 lb
find the tensile of the bolt with diameter 38mm,80kN
Please answer with explanation. Question : These two shear pins have the same length and same cross-sectional area. Both are subject to the same external tension load. Which pin has the lower shear stress? O a. The solid pin on the left. O b. The hollow pin on the right. O c. Both pins have the same shear stress.
Yivet (d) Hiw@. what aload (F) نهل reaquired to sperate the riveted plates shocwn in figure? = (80 (Givet) Fis = 1-7 ) Mpai d. (rivet) = 15 mm 12/24/2020
NEED ANSWER ASAP !!! The axial load 274 kN applied to the lap joint is distributed equally among the three 26.5-mm-diameter rivets. What is the bearing stress (in MPa) between a plate and a rivet if w = 135.4 mm and t = 29.5 mm?
3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all ~0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.
A 5⁄8-inch-thick tension member is connected to two 1⁄4-inch splice plates, as shown in Figure The loads shown are service loads. A36 steel and 5⁄8-inchdiameter, Group A bolts will be used. If slip is permissible, how many bolts are required? Each bolt centerline shown represents a row of bolts in the direction of the width of the plates.
Q1:Prepare a full-section assembly drawing of the four fastener assemblies shown in the Figure. Dimension both the clearance and the threaded holes. A top view may be shown if required. Scale 1: 1. .250-20 FHMS .375 HEX BOLT AND NUT THREADED INTO BASE 1.00 ↓ .50 T 2.00 Ø.375 STUD THREADED .312 HEX X 1.25 LG INTO BASE FOR 1.00 IN. CAP SCREW AND WITH HEX NUT AND LOCK WASHER ON SPOTFACE SURFACE PLATE WASHER A 2.00- -2.00 -1.00- BASE 1.00- .25 1.50
Pc=nxdxtxo =2x25x20x150 150000 N The strength of the riveted joint= Least of P, Ps , Pc =150 000 N %3D The lap join the edges of There are th %3D 000 050= 02I X 0Z X 001 ='91d=d 0000$ =D0.625 or 62.5 % %3D 0000 a-single tr Homework: 1-A single riveted lap joint is made in 1.5 cm thick plates with 2 cm diameter rivets Determine the strength of the joint, if the pitch of rivets is 6 cm? Take 6,=1200 kg/cm ; o,= 900 kg/cm² ; 6=1600 kg/cm 2-Two plates 16-mm thick are joined by á double riveted lap joint. The pitch of each row of rivets is 9 cm. The rivets are 2.5 cm in diameter. The permissible stresses are as aqnop -4 c-paraller [ans:2827kg] 2. G,=1400 kg/cm ; 6,=1100 kg/cm² ; 6.= 2400 kg/cm 2. Find the efficiency of the joint . 3-A double riveted double cover butt joint is made in 1.2 cm thich plates with 18 mm diameter rivets.find the efficiency of the joint for a pitch of 8 cm. 2. 2. ст Take :6,=1150 kg/cm ; 6, = 800 kg/cm² ; oc=1600 kg/cm 10 mm thick, the allowable stresses are : 6, =…
The hard copper containing solder (L-Cu) connection in Figure 4 is designed to be forced with a force of fully variable F 18000 N. What should be the distance I accordingly?
Find the size of 14 bolts required for C.I.steam engine cylinder head. The diameter of the cylinder is 400 mm and the steam pressure is 0.12 N/mm.