3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all -0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.

3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all -0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter22: Welding Joint Design And Welding Symbols

Section: Chapter Questions

Problem 4R: Sketch a V-grooved butt joint, and label all of the joint's dimensions.

See similar textbooks

Similar questions

The allowable tensile stress for a ½ bolt of thread length 7/32 inches is 30000 psi. The allowable shear stress of the material is 15000 psi. Where and how such a bolt most likely to fail, will it fail in the root diameter or the in the thread.
A 5⁄8-inch-thick tension member is connected to two 1⁄4-inch splice plates, as shown in Figure The loads shown are service loads. A36 steel and 5⁄8-inchdiameter, Group A bolts will be used. If slip is permissible, how many bolts are required? Each bolt centerline shown represents a row of bolts in the direction of the width of the plates.
A 3-in Aluminum plate and a 2-in cast-iron plate are compressed with one bolt and nut. The bolt is 7/8 in-9 UNC. (1) Determine a suitable length for the bolt, rounded up to the nearest in. (2) Determine the bolt stiffness. (3) Determine the stiffness of the members.
Find the size of 14 bolts required for C.I.steam engine cylinder head. The diameter of the cylinder is 400 mm and the steam pressure is 0.12 N/mm.
A 3/8-18 grade 8 bolt has 800 pounds of force pulling on it. Find the tensile force, the thread stripping strength for the needed length of engagement and the factor of safety for the bolt with that amount of force.
Sketch a V-grooved butt joint, and label all of the joint's dimensions.
Figure P1-71 shows a riveted butt joint with cover plates connecting two steel plates. Compute the 1-71. shear stress in the rivets due to a force of 10.2 kN applied to the plates.
A 2.5-in Aluminum plate and a 1.5-in cast-iron plate are compressed with one bolt and nut. The bolt is 3/8 in-16 UNC. (1) Determine a suitable length for the bolt, rounded up to the nearest 4 in. (2) Determine the bolt stiffness ks. (3) Determine the stiffness of the members km.
find shear amd Binding momont okagrou 5KN/m 5m Tht 3m 707
Assume a suitable value if any data is found missing. Two cylindrical pipes are to be used to make a medium drive fit. The nominal diameter of the assembly is 200 mm. The outer diameter of the outer pipe is 230 mm and the inner diameter of the inner pipe is 150 mm. Both the inner and outer pipes are made or aluminum. Assume that both the members have dimensions according to the prescribed tolerances for the kind of fit, determine the maximum and the minimum possible tangential stress in the outer cylinder.
Solve using Joints or Sectioning. Note that you have to state whether tensile or compression after solving each. Show the detailed step by step and complete solution.
Please answer with explanation. Question : These two shear pins have the same length and same cross-sectional area. Both are subject to the same external tension load. Which pin has the lower shear stress? O a. The solid pin on the left. O b. The hollow pin on the right. O c. Both pins have the same shear stress.