The figure shows a siphon discharging oil (s=0.90). The siphon is composed of 8 cm pipe from A to B followed by 10 cm pipe from B to C. The head losses are: Point 1-2: 0.30 J/N Point 2-3: 0.20 J/N Point 3-4: 1.00 J/N Compute the discharge. Determine the pressure at points 2 and 3. 8 cm ø - HEL. 5 m HEL. 3 m H10 cm Ø EL. O DATUM

The figure shows a siphon discharging oil (s=0.90). The siphon is composed of 8 cm pipe from A to B followed by 10 cm pipe from B to C. The head losses are: Point 1-2: 0.30 J/N Point 2-3: 0.20 J/N Point 3-4: 1.00 J/N Compute the discharge. Determine the pressure at points 2 and 3. 8 cm ø - HEL. 5 m HEL. 3 m H10 cm Ø EL. O DATUM

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
The pressure at point 2 shown in Figure is not to fall below 4.14 Bar when the flowrate from the tank is 0.028 m^3/ sec. Determine the minimum height, h, of the water tank under the assumption that (a) minor losses are negligible, (b) minor losses are not negligible. 3 m Figure No.3 Kentrance = 0.5 h The pipe is plastic of 15 cm diameter and (e/D=D0) 1.8 m (2) Main line 450 m with 15 elbows of 90 degree
Question 1. Water flows with a discharge of 0,020 through a SG pipe reducer as is shown in the Figure 1. The static pressures at 1st (Di=0,31 m) and 2nd (D2=0,18 m)cross-sections are measured by the inverted U- D2 tube manometer containing oil of specific gravity, SG as 0,7. Determine the manometer reading, h *(m). (1) Water Figure 1
Consider FIGURE R1M—3. Determine the discharge and the pressure head at A and B given a pipe diameter of 200 mm and the exit diameter to be 150 mm. Neglect losses of head.
1. Two tanks A and B have 70 m difference in water levels, and are connected by a pipe 0.25 m diameter and 6 km long with 0.002 friction coefficient. The pipe is tapped at its mid point to leak out 0.04 m3/s flow rate. Minor losses are ignored. (a) Determine the discharge leaving tank A? (b) Find the discharge entering tank B? ha А he B Q3 h = 70 m
Given a three-pipe system, the total pressure drop is PA - PB = 150,000 Pa, and the elevation drop is ZA ZB = 5 m. The pipe data are: Pipe 1 2 3 L, m 100 150 80 A. O 0.00283 m³/s O 0.00146 m³/s The fluid is water (density 1000 kg/m³ and kinematic viscosity 1.02x10-6 m²/s). Calculate the flow rate Q in m³/h through the system. (3 O 0.00675 m³/s O 0.00834 m³/s d, cm 8 6 4 1 €, mm 0.24 0.12 0.20 2 eld 0.003 0.002 0.005 • B
Water flows with a discharge of 0,02 through a SG pipe reducer as is shown in the Figure 1. The static pressures at 1st ( Di=0,3m) and 2nd ( D=0,1 m)cross-sections are measured by the inverted U- tube manometer containing oil of specific gravity, SG as 0,7. Determine the manometer reading, h *(m). (1) Water Figure 1
Subject hydraulics: Consider FIGURE R1M—3. Determine the discharge and the pressure head at A and B given a pipediameter of 200 mm and the exit diameter to be 150 mm. Neglect losses of head.
A pitot-static tube placed in the centre of a 300 mm pipe line has one orifice point- ing upstream and other perpendicular to it. The mean velocity in the pipe is 0.80 of the central velocity. Find the discharge through the pipe if the pressure difference between the two orifices is 60 mm of water. Take the co-efficient of pitot tube as C = 0.98.
An oil of viscosity 8 poise flows between two parallel fixed plates which are kept at 60 mm distance. The pressure drop over the length of 150 cm is observed to be 4.5 kPa. The width of the plates is 0.2 m. The discharge of flow (in Ips) is [Assume laminar flow.]
A horizontal Venturi meter with a throat diameter of 150 mm is connected a pipe of diameter of 250 mm to measure the discharge in the pipe. The pressures just upstream of the connection and at the throat were found to be 140 kPa and 80 kPa, respectively. Determine the flow rate in the pipe. Take the coefficient of discharge for the Venturi meter as 0.98 and T= 55°C. (Expected answer range: 0.190 m²/s
2. A pump discharge 126 of brine (sp.gr.=1.20). The pump inlet, 304.8 mm in diameter is at the same level as the outlet, 203.2 mm in diameter. At the inlet, the vacuum is 152.4 mm of mercury. The center of the pressure gauge connected to the pump discharge flange is 122 cm. The gauge reads 138 KPag. For a pump efficiency of 83%, what is the power output of the motor? 122 cm. PUMP