Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam

Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Water flows through Pipe A and into parallel pipes 1,2 and 3, and out through Pipe B. The properties of the pipes are listed as follows: Pipe Length (m) Diameter (cm) 30 Friction Coefficient, f A 1 300 10 0.020 240 600 2 15 0.018 3 20 0.017 В 30 The upstream junction (near A) has an elevation of 90m with a pressure of 205 KPa; the downstream junction is at elevation 30 m. If the average velocity in Pipe A is 3.0 m/s, find the pressure at the downstream junctions and rate of flow in each pipe. Also, draw the pipe system.
A liquid whose specific gravity is 2.0, is flowing in a 150mm diameter pipe. The total head at a given point was found to be 17.5m. That point is 3m above the datum and the pressure in the pipe is 65.6KPA. Compute the discharge in that point of the pipe. A) 29.05 L/s В No Answer among the choices 32.56 L/s D 24.31 L/s E 19.28 L/s
Subject hydraulics: Consider FIGURE R1M—3. Determine the discharge and the pressure head at A and B given a pipediameter of 200 mm and the exit diameter to be 150 mm. Neglect losses of head.
The figure shows a siphon discharging oil (s=0.90). The siphon is composed of 8 cm pipe from A to B followed by 10 cm pipe from B to C. The head losses are: Point 1-2: 0.30 J/N Point 2-3: 0.20 J/N Point 3-4: 1.00 J/N Compute the discharge. Determine the pressure at points 2 and 3. 8 cm ø HEL. 5 m HEL. 3 m H10 em g EL. O DATUM
WARH ALANBIYAA University of Warith Al-Anbiyaa, College of Engineering, Civil Engineering Department. VERSITY OF H.W(2):Water flows steadily from a large tank through a pipe that splits into two smaller pipes as shown in fig. Determine the flow rate from the tank and the pressure at point (1). 2017 a (0) 3 m (2) 7 m 0.03 m 0.05 m (3) m3 ,P =57.9 kPa f (1) Ans: Q = 0.00910 0.02 m
0.12 O -0.12 8.33 (1) Darcy Experiment A set-up of Darcy Experiment involves measuring the pressure head at two piezometers separated a distance, L. Given the set-up shown, determine the hydraulic gradient if the hydraulic head at (1) is 66 cm, hydraulic head at (2) is 54 cm, and the travel distance is 100 cm. O-8.33 -L h e - - - -
2. A 20mm diameter commercial steel pipe, 30m long is used to drain an oil tank. Determine the discharge when the oil level in the tank is 3m above the exit of the pipe. Neglect minor losses and assume f = 0.12. D=20mm, L=30 m, f-0.12 3 m
SN=23 SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be equal to SN/100 (m/s) (where SN is the sum of your student number). Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid-point of the pipe). Hi-300 m Ha datum A SN/1000 L- 100 x SN (m) D 0.3 m
Given a three-pipe system, the total pressure drop is PA - PB = 150,000 Pa, and the elevation drop is ZA ZB = 5 m. The pipe data are: Pipe 1 2 3 L, m 100 150 80 A. O 0.00283 m³/s O 0.00146 m³/s The fluid is water (density 1000 kg/m³ and kinematic viscosity 1.02x10-6 m²/s). Calculate the flow rate Q in m³/h through the system. (3 O 0.00675 m³/s O 0.00834 m³/s d, cm 8 6 4 1 €, mm 0.24 0.12 0.20 2 eld 0.003 0.002 0.005 • B
The fluid in the figure is water, with the surface 10m above the datum. The pipe is 15cm in diameter and the head losses are as follows: from 1 to 2, 0m; from 2 to 3, 0.60m; from 3 to 4, 2m; and from 4 to 5, 0.30m. 1.Determine the velocity of flow in the pipe in m/s. 2.Determine the discharge Q in m^3/s. 3.How many centimeters above the center of the pipe will water stand in piezometer tube 3? 4.How many centimeters above the center of the pipe will water stand in piezometer tube 4?
An oil of viscosity 8 poise flows between two parallel fixed plates which are kept at 60 mm distance. The pressure drop over the length of 150 cm is observed to be 4.5 kPa. The width of the plates is 0.2 m. The discharge of flow (in Ips) is [Assume laminar flow.]
Civil Engineering Water flows through two different pipes A and B of the same circular cross- section but at different flow rates. The length of pipe A is 1.0 m and that of pipe B is 2.0 m. The flow in both the pipes is laminar and fully developed. If the frictional head loss across the length of the pipes is same, the ratio of volume flow rates QB/QA is _(round off to two decimal places)