The figure below shows the cross section of unsymmetric I-beam. The I-beam experiences a maximum M=4 kNm sagging bending moment. And the beam is pulled apart with end-loading forces of 20 kN. Calculate the maximum tensile stress the beam experiences. (State your answer to the nearest whole number Mega-Pascals.) 120 mm T 60 mm 40 mm 30 mm 30 mm

The figure below shows the cross section of unsymmetric I-beam. The I-beam experiences a maximum M=4 kNm sagging bending moment. And the beam is pulled apart with end-loading forces of 20 kN. Calculate the maximum tensile stress the beam experiences. (State your answer to the nearest whole number Mega-Pascals.) 120 mm T 60 mm 40 mm 30 mm 30 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0, calculate the maximum load in N that the bar can support. A 12500*pi B 6250*pi 3125*pi 1563*pi
1. An axial force of 250 kN is applied to the assembly shown, made of cylindrical brass core surrounded by an aluminum shell. The axial force is applied through rigid end plates. a) Determine the normal stress in each of the metal components, given that Ebrass = 105 GPa and Ealum = 70 GPA. 100mm b) What is the axial deformation of the assembly? 200mm 200mm
The cantilever T- beam is loaded as shown in the figure. TE 80 mm 40 kN/m NA 120 mm 2.0 m Ina = 30x105 mm What is the value of maximum value of tensile flexural stress in MPa?
Mechanics of Deformable Bodies Problem: The figure shows the upper half of a built up girder( the cross section is symmetric about the neutral axis). All rivets used in fabrication have a diameter of 22 mm. The moment of inertia of the entire cross sectional area of the girder about the neutral axis is l=4770x10⁶mm⁴. The working stresses are 100 MPa for rivets in shear and 280 MPa for bearing of the web plate. If the maximum shear force carried by the girder is 450 kN, determine the largest allowable spacing of rivets that join the angles to the web plate.
The cantilever T- beam is loaded as shown in the figure. Ti 80 mm 40 kN/m NA --- 120 mm 2.0 m INA = 30x105 mm What is the value of fleure stress in a distance 1.20 m from the free end at the topmost fiber of the beam section?
Situation 6: The rigid bar of negligible weight is supported as shown in the figure. If W = 120 kN, There is a temperature change occur in the assembly and cause a tensile stress of 55 MPa in the steel rod. Use the following data: Bronze steel 1 m - 2 m O 4 m W 2 m 3 m 16. Compute the axial stress at bronze rod 17. Compute for the change of temperature 18. Compute for the vertical deflection at the W Steel Rod Bronze Rod A (mm²) 320 1500 a (/°C) 11.7 x 10-6 18.9 x 10-6 E (GPa) 200 83
Problem 1 A bar obtained by bonding together pieces of aluminum (E, = 70 GPa) and brass (E, = 105 GPa) has the cross section shown below. Considering that the allowable stress (both in compression and tension) of aluminum and brass are 120 MPa and 180 MPa, respectively, determine the largest moment M that can be applied about the horizontal axis. 8 mm 8 mm - 32 mm 8 mm 32 mm 8 mm - Brass - Aluminum Duoblesna 1
An aluminum-alloy block (E = 70 GPa) is loaded as shown in the diagram below. The application of this load produces a tensile strain of 500 x 10-6 at A as measured by means of a strain gage. Compute the magnitude of the applied force P and locate the neutral axis. 10 cm 15 cm 30 cm 2.5 cm Gage A
The beam shown is made of a nylon for which the allowable stress is 24 MPa in tension and 30 MPa in compression. Determine the largest couple M that can be applied to the beam. M = N•m A 15 mm ✓ 56 mm 28 mm 30 mm M
1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa Aluminum L=2m A=500mm 2m 2m E-72Mра P=20KN
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. Material Properties Material Area(mm2) E (GPa) Normal Stress(MPa) Bronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140 Aluminum 3P Bronze Steel 2P 4P - 0.6 m →- 1.0 m 0.8 m