A W12x72 column is an exterior 1st story column (red circled at gridline C) with strong axis buckling in the plane of the frame in an unbraced multi-story frame. The column above is also W12x72. Using the recommended stiffness G for the fixed base column, determine the effective length for this condition and the corresponding strength by LRFD. All steel is A992. 15 ft 1 15 ft W16x26 W16x26 30 ft B W18x35 W18x35 40 ft

A W12x72 column is an exterior 1st story column (red circled at gridline C) with strong axis buckling in the plane of the frame in an unbraced multi-story frame. The column above is also W12x72. Using the recommended stiffness G for the fixed base column, determine the effective length for this condition and the corresponding strength by LRFD. All steel is A992. 15 ft 1 15 ft W16x26 W16x26 30 ft B W18x35 W18x35 40 ft

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.7.13P

See similar textbooks

Similar questions

If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
ASSIGNMENT #5 BIAXIAL BENDING Problem: Check the beam shown for compliance with the NSCP Specification. Lateral support is provided only at the ends, and A992 steel is used, F, = 345 mPa. The 90 kN service loads are 30% dead load and 70% live load. a. Use LRFD b. Use ASD d tw by ty 1x(106) S(10³) mm mm mm mm³ mm mmª W410x100 415 10 260 16.9 398 1920 SECTION Tx mm 177 1m 90 kN 90 KN 1.5m W410x100 I Loaded Section Ly(106) Sy(10³) Ty mmª mm³ mm 49.5 381 62.4 1m Zx(10³) Zy(10³) mm³ mm³ 2130 581
A simply supported beam is subjected to a uniform service dead load of 1.0 kips/ft (including the weight of the beam) and uniform service live load of 2.5 kips/ft. The beam is 40 feet long, The beam has continuous lateral support, and A572 Grade 50 steel is used. A572 Grade 50 steel has Fy = 50 ksi and Fu = 65 ksi. Is a W30 × 116 adequate from flexure and shear?Check both LRFD and ASD. Is the beam adequate from deflection if it allowsmaximum deflection of L/360 (dead load + liveload)?
HOMEWORK-1 3m IF For the truss shown in the figure; Design members 1-2 and 2-3 assuming that out of plane deflections are restrained and Ner>>10, i.e. global buckling is not the critical failure mode and therefore linear static analysis is sufficient. P.S. Use square rectangular hollow sections in Grade 355 steel. You will have to find the related section tables from the internet. Do not forget to refer to the related EN1993-1-1 tables and equations. Later, you will design the connections (the weld lengths, etc.) and the supports for this problem.
determine the member stresses of the truss shown. indicate if the stress in the member is in tension or compression. present complete and neat solutions. p1-30kN W-25kN/m P2=51kN AH Av Im P₂ Im P₂ Im P₂ Im Av W 1.6m
SITUATION 2 Determine the safe service load W permitted for this beam-column that is not part of a frame system. Assume ASTM A992 (Fy = 350 MPa; Fu = 450 MPa) as material. Use LRFD specifications. Servise koada P= 30 kips dead load 80 kips live koad Assume hinged for both principal 10- 0 directions W- 20 dead load 8OG live load 10-o Fined for both principal directions Type your final answer/s in the text box provided below.
Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.