The axial flow pump produces a discharge of 0.035 m³/s. (Figure 1) The impeller is rotating at w = 50 rad/s, and it has a mean radius of 75 mm. The diameter of the impeller's shaft is 100 mm. Part A Determine the magnitude of the velocity of the water as it exits the blades. Express your answer to three significant figures and include the appropriate units. V₂ = 2.86 μA m S ?

The axial flow pump produces a discharge of 0.035 m³/s. (Figure 1) The impeller is rotating at w = 50 rad/s, and it has a mean radius of 75 mm. The diameter of the impeller's shaft is 100 mm. Part A Determine the magnitude of the velocity of the water as it exits the blades. Express your answer to three significant figures and include the appropriate units. V₂ = 2.86 μA m S ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A centrifugal pump delivers 25 liters of water per second against a head of 10 meters and running at 1300 rpm requires 10 kW of power. Determine the discharge, head of the pump and power required if the pump runs at 1500 rpm. (Ans. 0.0288cumec or 1.73 cu.m./min , 13.31m, 15.36kw)
A pump with an impeller diameter of 300 mm running at a speed of 2950 rev/min delivering 450 L/min of water at a head of 350 kPa is going to be replaced by a geometrically similar spare pump running at a speed of 1450 rev/min delivering the same flow rate and head. Determine the impeller size of the spare pump and the percentage increase (decrease) of power required for the spare pump. OL. 380.1 mm; a decrease of 61.33% OI., 380.1 mm; an increase of 38.77% I. 147.5 mm; an increase of 3.4% IV. 210.3 mm; a decrease of 83.1%
Problem 1(5): A centrifugal pump transports water between two reservoirs. The pump has an outer diameter of 15 cm, an inner diameter of 8 cm, and a blade width of 2 cm and operates at 1750 rpm. If the water enters the pump axially at ẞ₁ = 45º¸ compute the volume flow rate, Problem 2(10): In the pump of problem 1, the water exits at B₂ 65° when the pump is driven at 1750 rpm. = Compute the minimum power required by the pump?
- A centrifugal pump with an impeller diameter of 350mm and specific speed of 19.15 and requires 15 kW to discharge 2.4 m³ /min of water, and runs at 1800 rpm. Determine the discharge, head and power required when the pump runs at 2400 rpm. The same discharge could be obtained by altering the impeller diameter without changing the rotational speed for this case find the new diameter of the impeller the head and the power required.
C. A pump delivers 25 L/s of water with a head of 35 m and runs at a speed of 2950 rpm for 8 hours per day. The shaft power is 11.5 kW. The electric motor driving the pump has an efficiency of 84% and the cost of electricity is 15 cents per kWh. Evaluate the cost of electricity to run the pump in a day.
A vessel is being filled with water through an inlet at section 1 having a diameter of 40 mm and a faucet at section 3. The velocity at section 1 is given as 5 m/s, while the discharge at section 3 is given as 0.012 m^3/ s. Assume constant water level. Use 60 mm for the diameter of the outlet at section 2. A. What is the discharge at section 2? B. What is exit velocity at section 2? C. If the water level varies and the velocity at section 2 is 8m/s find the rate of change when d is equal to 1000mm?
18. A centrifugal pump has to work against a head of 25 metres at a speed of 850 rpm. The flow component of the velocity at outlet is 2'5 metreajeccond. The outlet vane angle is 40°. If the discharge of the pump is 0 25 cumeo find (i) The diameter of the impeller and (ii) The width of the impeller at outlet. Neglect losses. (0:387 m; 0'082 m)
Q1 A centrifugal pump operates at a speed of 1150 r/min and discharges 2.3 m' /min against a head of 120 kPa. The power required is 8.2 kW. Compute (a) the efficiency of the pump, (b) the discharge, head, and power if the pump speed were changed to 1750 r/min.
In a medical water treatment station, there is a centrifugal pump. The pump delivers a flow rate of 0.003 m3/s. The pump radius is 0.3 m. The water enters axially and leaves the impeller relative to radial blades at the exit. Theoretically using Euler turbomachine equation, what should be the rotation speed for the pump to develop a head of 9 mH2O? Give your answer in rotation per minutė (rpm).
A multi stage pump is required to deliver of 2 l/s water against a maximum discharge head of 240 m. The diameter of radial bladed impeller should not be more than 15 cm. Assume a speed of 2800 rpm. Determine the impeller diameter, and power. Overall efficiency is 0.7.
QUESTION 1 A jet of freshwater strikes a series of vanes of a turbine at 25° with the direction of motion and leaves it at 150° absolute with the direction of motion. The absolute inlet velocity of the jet is 25 m/s and the vanes move at a velocity of 10 m/s. Ignore friction across the vanes. Calculate:
H.W: The inlet diameter of the centrifugal pump, shown in figure below, is 28 in. and the outlet flow through the pump is 9200 lb/s. The density of the water is 49 lb/ft. What is the velocity at the pump inlet? Ib m = 9200 sec 28 in. V = ? --