Please help Show that the equation of continuity in fluid mechanics satisfies dimensional homogeneity.In fluid mechanics, the differential form of the equation of continuity is given byOpƏtV v= -V.(pu)where p is fluid density; t is time; u is the flow velocity vector; V is the Del operator (also knownas the nabla operator; see its Wiki page for further references). In 3D cartesian coordinate system,u = (Ux, Uy, Uz), and=(2)Ə Ə Ə?х' ду' дz(3)

The equation is ∂ρ∂t=-∇.ρu where ρ is the fluid density, t is time, and u is the flow velocity…

Show that the equation of continuity in fluid mechanics satisfies dimensional homogeneity. In fluid mechanics, the differential form of the equation of continuity is given by др Ət -V. (pu) where p is fluid density; t is time; u is the flow velocity vector; V is the Del operator (also known as the nabla operator; see its Wiki page for further references). In 3D cartesian coordinate system, u= (Ur, Uy, uz), and V = ə ə ә ar' au' az (3)

Show that the equation of continuity in fluid mechanics satisfies dimensional homogeneity. In fluid mechanics, the differential form of the equation of continuity is given by др Ət -V. (pu) where p is fluid density; t is time; u is the flow velocity vector; V is the Del operator (also known as the nabla operator; see its Wiki page for further references). In 3D cartesian coordinate system, u= (Ur, Uy, uz), and V = ə ə ә ar' au' az (3)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Tp = Fq +°P/Q• (1) Here ip/Q is the "position of point P relative to point Q." Similarly the velocities of the two points are related by õp = bq + Up/Q- (2) The quantity õp/Q is the velocity of point P relative to point Q. I want you to use these ideas to solve the following problems. 1. The figure below shows a view from above of a large boat in the middle of the ocean. So that the crew on the ship can get exercise on long journeys, there is a circular walking/running track on the back deck. CA B- -D Suppose that the radius of the track is R = 6 m, and a person is running on the track at a constant speed of v = 3m/s as measured with a stopwatch by a crew-mate on board the ship. Suppose the runner is running counter-clockwise around the track when viewed from above. Write the velocity vector of the runner in terms of basis (ê1, ê2) as perceived by a crew-mate on the ship. (a) What is the velocity vector when the runner is at point A? (b) What is the velocity vector when the runner is…
At a particular time, the polar coordinates of a point P moving in the x-y plane are r = 4 m, 0 = 0.5 rad, and their time derivatives are dr/dt = 8 m/s and d0 /dt the velocity P, (b) What are the cartesian components of the velocity %3D %3D -2 rad/s. (a) What is the magnitude of %3D P? mB Art
1- The thrust (P l ) of a propeller depends upon diameter (D); speed (u) through a fluid density (p); revolution per minute (N); and dynamic viscosity (u) Show that: P = (p D² u²) f P Du [; where fis any function.
Q2: The coordinates of a particle in the metric xy-plane are differentiable functions of time t with dxldt =-1 m/sec and dyldt = -5 m/sec. How fast is the particle's distance from the origin changing as it passes through the point (5, 12)?
A mechanic changing a tire rolls a wheel along the ground towards the car. The radius of the wheel is 42cm, and the speed of the wheel as it rolls is 2 revolutions per second. Height Above Ground (m) radiu HIDE wheel spet Time The diagram above illustrates the vertical motion of a point on the tire over time. It is possible to model the height of this point using a sinusoidal function of the form h(t)=-a sin[b(t-c)]+d. a) Determine the length of time required for one revolution of the tire. b) State the numerical value for each of the parameters a, b, c & d. And write a function representing the motion of the point in the form h(t)= -a sin[b(t−c)]+d.
An object of mass m is being affected by the force F = cxx, where c is a positive constant. The object leaves the origin with a speed i, at timet = 0. Find x(x). Answer to Question 1 [Insert solution image after this line]: %3D %3D
If the following equation is dimensionally homogeneous, find the dimensions of the physical quantity K indicated in the system of fundamental physical quantities: Length, Mass and Time. Ep -G Mm K where Ep is the gravitational potential energy (same units as the kinetic energy E mv²/2), M and m are the mass of the earth and the mass of the body, respectively, and G is the universal gravitation constant G~ 6,67 x 10-11 N m² kg²
Which of the following dimensions belongs in the set (force, velocity, acceleration, magnetic field}? * mass speed displacement temperature When two vectors are perpendicular, their * dot product is zero cross product is zero. both are zero both are not necessarily zero The cross product of tWO vectors 3İ + 4j -5k and-i+j- 2k is
When a liquid in a beaker is stired, whirlpool will form and there will be an elevation difference h, between the center of the liquid surface and the rim of the liquid surface. Apply the method of repeating variables to generate a dimensional relationship for elevation difference (h), angular velocity (@) of the whirlpool, fluid density (p). gravitational acceleration (2), and radius (R) of the container. Take o. pand R as the repeating variables.
Check the following equation for dimensional homogeneity: mu = (Fcos) at where m is mass, v is velocity, F is force, is an angle, and it is time. Check that each term in the equation has the following dimensions: [MOLT] where you are to choose the coefficients a, b, c. Answers: b= C= i i
Example: Give the primary dimensions (T): Time. [Ml: Mass and (: Length) and one of suggested units of the following magnitudes based on the mentioned definition. Use the definitions explained below to conclude the reguired information: depthxaccelaration (elevation xweight /volum time X2 = X1 = X3 = stress mumber elongation mumber length mass/volum X4 = X5 = shear forcextime velocity area/time area thickness
. I am planning to perform some volume-flow rate measurements in the Fluid Mechanics Laboratory. For this, I need a volumetric measuring tank (graduated cylinder) and a stopwatch. I considered the volume of the measured tank as 15 gallons and a stopwatch with reaction time as 1/10th of a second (though resolution of 1/1000th of a second). What is the volume flow rate if it takes 5 minutes to fill a 15-gallon of tank? Determine the smallest division to be on the tank in order to estimate the volume flow rate within an accuracy of ± 0.05 gpm.