I am planning to perform some volume-flow rate measurements in the Fluid Mechanics Laboratory. For this, I need a volumetric measuring tank (graduated cylinder) and a stopwatch. I considered the volume of the measured tank as 15 gallons and a stopwatch with reaction time as 1/10th of a second (though resolution of 1/1000th of a second). What is the volume flow rate if it takes 5 minutes to fill a 15-gallon of tank? Determine the smallest division to be on the tank in order to estimate the volume flow rate within an accuracy of ± 0.05 gpm.

I am planning to perform some volume-flow rate measurements in the Fluid Mechanics Laboratory. For this, I need a volumetric measuring tank (graduated cylinder) and a stopwatch. I considered the volume of the measured tank as 15 gallons and a stopwatch with reaction time as 1/10th of a second (though resolution of 1/1000th of a second). What is the volume flow rate if it takes 5 minutes to fill a 15-gallon of tank? Determine the smallest division to be on the tank in order to estimate the volume flow rate within an accuracy of ± 0.05 gpm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ql: The viscosity in industrial measurement continue to use the CGS system of Lunits, since centimeters and grams vield convenient numbers for many fluids. The absolute viscosity () unit is the poise, I poise = 1 gtem. s). The kinematic viscosity (v) unit is the stohes, I stokes = 1 em /s. Water at 20C has u = 001 poise and also V= 0.01 stokes. Express these resalts in (a) SI and (h) BG tanits.
Time left 1:5 An ideal gas has its pressure (1.8) times and mass density (2.2) times increased. If the initial temperature is 265.4 °C, what is the final temperature in °C, and use one number after the decimal (xxx.x)? Answer: NEXT PAGE pe here to search DELL
Assignment 3 On Viscosity Calculation - Word TOUT REFERENCES MAILINGS REVIEW VIEW Hyperlink P Bookmark tArt Chart Screenshot Apps for Office Online Video Cross-reference Comment Header Footer Page Number Text Quick WordA Box Parts - ns Apps Media Links Comments Header & Footer (2) Referring to the following figure, the distance between plates is Ay = 0.5 cm, Av: = 10 cm/s, and the fluid is ethanol at 273 K having a viscosity of 1.77cp (0.0177 g/cm s). (a) Calculate the shear stress ty and the velocity (b) gradient of shear rate -/dy using cgs units. (c) Repeat using SI units. A Torce Fdshear berween teoparailel plates
Check the following equation for dimensional homogeneity: mu = (Fcos) at where m is mass, v is velocity, F is force, is an angle, and it is time. Check that each term in the equation has the following dimensions: [MOLT] where you are to choose the coefficients a, b, c. Answers: b= C= i i
10 The Reynolds number is a dimensionless quantity used in calculations of fluid flow in pipes. The Reynolds nummber is defined as D,Vp NRe where D; is the inside diameter of the pipe, V is the average velocity of the fluid in the pipe, p is the fluid density and u is the absolute viscosity of the fluid. For flow in pipes, a Reynolds number of less than 2000 indicates that the flow is laminar, while a value of greater than 10,000 indicates that the flow is turbulent. For a pipe diameter of 5 cm, and fluid of density 1 g/cm and viscosity of 1 centipoise, find the minimum velocity that results in turbulent flow.
The velocity of the fluid flowing in a pipe with a radius of 10 cm was measured at certain points and the following table values were obtained. r=the distance of the measurement points to the center of the pipe (m) v=measured speeds (m/s) Accordingly, calculate the velocity value for r = 0.07 m by using 3rd order interpolation with the help of appropriate points that make the error minimum. In calculations, take 4 digits after the comma.
Water X 50-mm inside diameter The volume flow rate of the system The pressure at the point "A" The pressure at the point "B" 25-mm diameter As a consultant at one of the country's leading soft drink companies, you are tasked with evaluating the system depicted to determine the following parameters using Bernoulli's Equation if the values assigned to "X" and "Y" are 3m and 0.5m respectively: i. ii. iii.
The friction in flows through the pipe is defined by a dimensionless number called the fanning friction factor (f). The Fanning friction factor is represented by another dimensionless number, the Reynolds number (Re).It depends on the diameter of the pipe and some parameters related to the fluid. An equation that can predict f given the Reynolds number is given as follows. If Re =4000, e/D=0.01 in this equation, find the value of f using the Simple Iteration method by taking f0=0.1 as the initial value for the solution (ԑ=0.0001)
Thermal conductivity k is a measure of the ability of a material to conduct heat. For conduction heat transfer in the x-direction through a surface normal to the x-direction, Fourier’s law of heat conduction is expressed as: Q=-kA.dT/dx where ?̇ is the rate of heat transfer and A is the area normal to the direction of heat transfer. Determine the primary dimensions of thermal conductivity (k). Look up a value of k and verify that its SI units are consistent with your result. Write a set of primary SI units for k.
As we explained in earlier chapters, the air resistance to the motion of a vehicle is something important that engineers investigate. The drag force acting on a car is determined experimentally by placing the car in a wind tunnel. The air speed inside the tunnel is changed, and the drag force acting on the car is measured. For a given car, the experimental data generally is represented by a single coefficient that is called drag coefficient. It is defined by the following relationship: F, where air resistance for a car that has a listed C, = drag coefficient (unitless) measured drag force (N) drag coefficient of 0.4 and width of 190 cm and height of 145 cm. Vary the air speed in the range of 15 m/s
Check the following equation for dimensional homogeneity: mv = = 1.5² (Fcose) dt where m is mass, v is velocity, F is force, is an angle, and t is time. Check that each term in the equation has the following dimensions: [MªLbTC] where you are to choose the coefficients a, b, c. Answers: a = i b = i C=
Good day. I require assistance as this will help in my examination review. (Basic Aerodyn Principles) A circular pipe 57 meters long tapers from 3 m to 2 m in diameter. What is the velocity per meter run at the bigger section, if the velocity there is 39 mps, and the fluid is flowing from the larger section to the smaller section? Round-off answer to the nearest hundredths. **Would gladly appreciate an explanation. Thank you.