low voltage systems In the reverse phase, a 1000 kw powerful load under 0.5 power factor is fed from a 5 kv source. A capacitor is connected in parallel with the load to increase the power factor to 0.8. a-) Find the required capacitor power. b-) Compare the apparent power before and after compensation.

low voltage systems In the reverse phase, a 1000 kw powerful load under 0.5 power factor is fed from a 5 kv source. A capacitor is connected in parallel with the load to increase the power factor to 0.8. a-) Find the required capacitor power. b-) Compare the apparent power before and after compensation.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
15. You are working on a power factor correction installation, and you notice with a clip-on ammeter as you add in capacitance the current drops, you add more capacitance and the current drops, you add more capacitance the current rises. How do you know when you are at unity power factor?
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
An inductor and a 470 ohm resistor are connected in series with a function generator. The current is 53.7mA RMS 8kHz. The reactive power is 2.32 var. Find the value of the inductance.
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
4- A Circuit of zero lagging power factor behaves as a. A capacitive circuit b. An inductive circuit c. RC circuit d. RL circuit
Calculate the value of capacitance in the following figure that must be connected in parallel with the load to correct the source power factor to 0.94 lagging. The frequency f = 60 Hz
1. Enumerate five formulas for five series connected inductances across Vt source and draw the circuit. 2. Enumerate five formulas for five parallel connected inductances across Vt source and draw the circuit.
A 230 V, 50 Hz a.c. supply is applied to a coil of 0.06 H inductance and 2.5 resistance connected in series with a 6.8 F capacitor. Calculate impedance and power consumption and power factor. Now ,In above a.c. circuit, A inductor of 0.2H is connected in parallel with the power supply, find new power factor and power consumption.