<02.1-6 Fluid Statics: Pressure Variation Item 6 Due to its slight compressibility, the density of water varies with depth, although its bulk modulus Ey= 2.20 GPa (absolute) can be considered constant. Part A Accounting for this compressibility, determine the gage pressure in the water at a depth of 700 m, if the density at the surface of the water is po 1000 kg/m³ Express your answer to four significant figures and include the appropriate units. View Available Hint(s) Pcompressible 6.86 Submit 0 Part B μA Previous Answers MPa X Incorrect; Try Again; 3 attempts remaining ? Assuming water to be incompressible, determine the gage pressure in the water at a depth of 700 m Express your answer to four significant figures and include the appropriate units. ▸ View Available Hint(s)

<02.1-6 Fluid Statics: Pressure Variation Item 6 Due to its slight compressibility, the density of water varies with depth, although its bulk modulus Ey= 2.20 GPa (absolute) can be considered constant. Part A Accounting for this compressibility, determine the gage pressure in the water at a depth of 700 m, if the density at the surface of the water is po 1000 kg/m³ Express your answer to four significant figures and include the appropriate units. View Available Hint(s) Pcompressible 6.86 Submit 0 Part B μA Previous Answers MPa X Incorrect; Try Again; 3 attempts remaining ? Assuming water to be incompressible, determine the gage pressure in the water at a depth of 700 m Express your answer to four significant figures and include the appropriate units. ▸ View Available Hint(s)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Select the correct value of H: ( The density of liquid =990 kgim, gravity g = 9.81 mis and L= 90 cm, Pressure P1= 52.369 Kpa) Air Pt Liquid (2)
H.W.1/: The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown in Fig. below. Determine the gage pressure of air in the tank if hl = 0.4 m, h2 = 0.6 m, and h3 = 0.8 m. Take the densities of water, oil, and mercury to be 1000 kg/m³, 850 kg/m³, and 13600 kg/m3, respectively? Oil Air Water IT h2 h3 Mercury
P1.5 An artificial solar pond is a body of water with a density gradient created by adding salt to the water. Obtain an expression for the variation of pressure P with depth - assuming the density distribution to have the linear form, p(=) = p, + az, where Po is the density at the surface and a is a constant. The ambient pressure is Po. [Answer: P(z) = P, + gz(p. + az /2)]
An inverted differential manometer containing an oil of sp. gr. 0.9 is connected to find the difference of pressures at two points of a pipe containing water. If the manometer reading is 40 cm, find the difference of pressures. [Ans. 392.4 N/m²]
In the piezometers of the figure shown, liquid stands 1.37 m above point M. What is the pressure at M in kPa if the liquid is (a) water, (b) oil (sp gr 0.90), (c) mercury, and (d) molasses (spgr 1.5). B MATHalino.com TICAL Reimagine Education. www.disi.edu.ph
(Vi1) energy (viii energy energy (X) energy 3. What is the temperature of heated air at 150°C in °F, K and Rankine. 4. A manometer is used to measure the pressure in a tank. The fluid inside the manometer specific gravity is 0.85 and the absolute pressure within the tank is 100.6 kPa. Calculate the column height in mm. Take atmospheric pressure is 96 kPa. 5. Consider a differential manometer whose ends are connected to two different pipes A and B and
1. The deformation of the fluid will continue as long as the 2. When designing gates, vessels, dams or other bodies that are submerged in a liquid, it is important not only to estimate the - 3. The surface tension is the tensile force per --- in any direction along the surface the surface tension. 4. The value of --- specifies whether the fluid can be assumed compressible or incompressible. 5. Archimedes' principle indicates --- 6. A truck is filled with gasoline. Ifr the container (tank) on the truck undergoes a - , then the liquid is applied. --- but also to specify its location on the body. surface will begin to rotate clockwise about the center of the container and will eventually maintain a fixed tilted position.
1:0A Question.pdf > Question Q:-Determine the force exerted on the cone curved surface. The liquid in the tank has a specific weight of 27 kN/m' and the absolute pressure of the air in the tank is 151 kPa. 151 kPa Absolute Air Liquid 3m 1 m Cone Good Luck Prof.Dr. Muhammad A.Eleiwi II
A cylinder contains a fluid at a gauge pressure of 350kPa. Express the pressure in terms of the column height of (a) water (p = 1000kg/m) (b) Hg (S = 13.6). What would be %3D absolute pressure in the cylinder if the atmospheric pressure is 101.3 kPa ?
(b) Prove that the pressure in a static fluid varies with depth in accordance with the relation: dp dz Where p - pressure in fluid -pg z-depth with respect to as specified datum p-fluid density g-acceleration due to gravity
Q2:0 A water Storage tank contalns liquid and Vapour in equi'libruim at ilo2. The distance from bottom of the level is 8 m. What is the absolute pressure at the bothom of the tank. tank to the Liquid [218 kpa]
M1 U5: Use the general solution in determining the total hydrostatic force acting on the submerged curved surface. Please provide the complete UNITS ANALYSIS, USE OF CORRECT CONVERSION RATIOS and DIAGRAMS in your hand-written solution. INCOMPLETE/NO SOLUTION means NO CREDIT. Encode your FINAL answer in the space provided after each question. A curved surface is formed as a quarter of a circular cylinder with R = 0.75 m as shown. The surface is w 3.55 m wide. Water stands to the right of the curved surface to depth H = 0.60 m. seawater 0.60 m (SG = 1.03) %3D 0.75 m Determine the magnitude and direction of the horizontal component of the hydrostatic force (in N) acting on the gate. Indicate the direction by putting an R for right and L for left after your numerical answer. Your answer