A cylinder contains a fluid at a gauge pressure of 350kPa.Express the pressure in terms of the column height of(a) water (p = 1000kg/m) (b) Hg (S = 13.6). What would be%3Dabsolute pressure in the cylinder if the atmospheric pressureis 101.3 kPa ?

Answered: Image /qna-images/answer/5bbedce4-f428-4f6b-9671-775cfe9a270f.jpg

cylinder contains a fluid at a gauge pressure of 350kPa. xpress the pressure in terms of the column height of ) water (p = 1000kg/m") (b) Hg (S = 13.6). What would be %3D psolute pressure in the cylinder if the atmospheric pressure 101.3 kPa ?

cylinder contains a fluid at a gauge pressure of 350kPa. xpress the pressure in terms of the column height of ) water (p = 1000kg/m") (b) Hg (S = 13.6). What would be %3D psolute pressure in the cylinder if the atmospheric pressure 101.3 kPa ?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 14RQ: Atmospheric pressure at sea level under standard conditions is ______inches of mercury (Hg) or_____...

See similar textbooks

Related questions

Q: A single-angle tension member, an L3 12 x 3 12 x 38, is connected to a gusset plate with 7/8-inch-di...

A: Strength of single angle with gusset plate is totally dependent on gross area and net area of the pl...

Q: A Carnot engine delivers 130 kW of power by operating between temperature reservoirs at 160°C and 16...

A: GivenPower P=130kWT1=160oC=160+273=433KT2=1660oC=1933Kt=26min =26×60 s

Q: ner is subjected to the force of F = 20 lb. Determine the out the point A.

A: Given data F=20lb

Q: is to be monitored by a differential pressure cell responding to the difference in pressure between ...

A: solution of above question is below:

Q: Explain the "burst potatoes in the boiling water" with thermodynamic viewpoint.

A: Whenever potatoes are boiled in the water, there is heat transfer from the hot water to the potato. ...

Q: Superheated steam at 7.585 MPa (1100 psia) and 616.3 K (650 F) enters the high-pressure turbine of a...

A: At state 1 : Saturated water and P1=7kPa h1=163.3655 kJ/kg v1=.0010075 m3/kg Wp1=h2-h1=v1∆P h2-163.3...

Q: a. The required gap so that the rails just touch one another when the temperature is increase p. Wha...

Q: A steel rod, which is free to move, has a length of 200 mm and diameter of 20 mm at a temperature of...

Q: m.K carries a fluid at 200°C, with a convection heat transfer coefficient of 210 W/m2./K. The tube h...

Q: 6.2 In class we noted that the potential energy of a spring is given by Vsp(2) = k(z – zo)² /2, wher...

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for...

Q: Situation - An eccentrically loaded bolted connection is shown in the figure below. Diameter of A325...

Q: 311(MECHANICS OD DEFORMABLE BODIES): PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPO...

Q: Enumerate and explain the different parts of diesel engine. As shown in figure below.

A: A diesel engine is an internal combustion engine that converts the energy in diesel fuel into rotati...

Q: A cantilever beam, 80 mm wide by 270O mm high and 8 m long, carries a load that varies uniformly fro...

A: Draw a diagram for the cantilever beam. Here, w1 is the load intensity at point B i.e. at 5 m from ...

Q: The ball at A is kicked such that 0A = 57 •. It strikes the ground at B having coordinates x = 15 ft...

A: Find the velocity of ball at kicked and strike the ground

Q: Given a rectangular plate which is deformed as shown by the broken line. Determine the average shear...

Q: (Problem 2) Alcohol (specific gravity = 0.80) is flowing through a horizontal pipe which is 10 inche...

A: Write the Bernoulli's equation between the smaller cross-section pipe and the larger cross-section. ...

Q: The number of degree of freedom

A: Given; The number of degree of freedom of a planar linkage: 22 links and 27 simple revolute joints....

Q: a) Briefly explain the application of CAD/CAM in Textile industry field. b) (How CAD/CAM is used, Be...

A: a}Application of CAD/CAM in textile industry : 1.To create different types of designs using CAD soft...

Q: How is thermal energy lost when a person exits a building through an exterior door in the winter? a)...

A: Convection is the transfer of heat from one section of a fluid (liquid or gas) to another by the ...

Q: A 1.3-lb sphere A is dropped from a height of 1.8 ft onto 2.6-lb plate B, which is supported by a ne...

Q: 1.) 0.44 kgm of air at 1800C expands adiabatically to three times its original volume and during the...

Q: A horizontal water pipe is reduced in size from 18 inches in diameter from point A to 6 inches in di...

A: Diameter at A, DA=18 in=1812ft=1.5 ftDiameter at B, DB=6 in=612ft=0.5 ftWater flow rate, Q=10 ft3/sP...

Q: A cylindrical aluminum alloy 10 mm in diameter and 70 mm long is pulled in tension with a force of 8...

A: Answer: (a) The specimen elongation is 0.21 mm. (b) The reduction in specimen diameter is 0.0099 mm....

Q: Q11 Find the reactions in supports

Q: The maximum radial load

A: Given: The dynamic load capacity of 6306 bearing is 22 KNMaximum radial load it can sustain to opera...

Q: Relative velocity of link 1 with respect to link 2 is 20 m/s. link 2 rotates at constant speed 140rp...

A: Given:Relative velocity of link 1 with respect to link 2, v=20 m/sSpeed of link 2, N=140 rpm

Q: A four bar mechanism is made up of links of length 100,200,300 and 350 mm. if the 350 mm link is fix...

A: Since, the sum of the longest link and the shortest link is 450mm which is less than the sum of the ...

Q: 18. In the following unit cell, which vector represents the [121] direction? B +y +x A d. D а. b. В ...

Q: The water flow rate through the vertical bend shown in the figure is 2.83 m³/s. Calculate the magnit...

Q: What is the height difference reading on the U-Tube? * contraction 1. Consider a low speed subronic ...

A: Given data Area of nozzle inlet = A1Area of test section = A2Given area ratio = A1A2 = 121Velocity a...

Q: A pelton wheel is having a mean bucket diameter of 1m a running at 1000 rpm. The net head on pelton ...

A: Given:Mean bucket diameter, d=1 mSpeed, N=1000 rpmNet head, H=700 mDischarge, Q=0.1 m3/sSide clearan...

Q: The above left drawing shows a countershaft with helical gear B, bevel gear D, and two supporting be...

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 8) Determine load P that c...

Q: The suction pressure of a pump reads 650 mm Hg vacuum. What is the absolute pressure in kPa? Choice...

Q: A cylindrical object 85mm diameter, 157mm height and a mass of 601g, is placed in the tank, which co...

Q: A 55-mm-diameter solid circular shaft as shown in the figure is made up of an aluminum material. The...

Q: Consider a W14x43 (Fy = 100 ksi) used as a compression member in a truss with Lc = 5 ft. What is the...

A: Find the strength of column about weak axis

Q: nt is 1/28 and the t

Q: B. A Highway Engineer tabulates the following ADT for the Highway that will be constructed. the dail...

A: AADT* k factor = hourly volume design The k factor is the hourly volume adjustment factor for the de...

Q: How much solar energy is captured if 100ml of water is raised 10 degrees over 10 minutes using a 10c...

Q: Use the moment-area theorems and determine the slope at A and deflection at A. El is constant.

A: Given: A cantilever beam having point load at free end,

Q: The pressure in a section of a horizontal pipe of diameter d1 = 2.0 cm is p1 = 142 kPa. The water fl...

Q: Problem 2 State whether the following statements are true or false. In either case, give the reasoni...

A: a).True,Acceleration is defined as the derivative of velocity w.r.t time,ie |a|=dv/dt b).True,If bod...

Q: 1. A) Draw the mean effective pressure vs specific fuel consumption at constant speed and constant t...

A: Mean effective pressure The mean powerful tension (MEP) is an amount connecting with the activity o...

Q: Determine the maximum tensile stress (MPa) at

A: Determine maximum tensile stress.

Q: A generating unit of 10 MW capacity supplies the following loads: Domestic consumers with a maximum ...

Q: 1. Find the magnitude and direction of the resultant force for the system of forces shown in the fig...

Q: O Summing moments about an axis parallel to x, passing through A Summing moments about an axis paral...

Q: 19. The surface of a circular dartboard has a small center circle called the bull's eye and 20 pie-s...

Question

A cylinder contains a fluid at a gauge pressure of 350kPa.
Express the pressure in terms of the column height of
(a) water (p = 1000kg/m) (b) Hg (S = 13.6). What would be
%3D
absolute pressure in the cylinder if the atmospheric pressure
is 101.3 kPa ?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. A closed vessel contains air at a pressure of 160 kN/m2 gauge and temperature of 30oC. The air is heated at constant volume of 60oC with the atmospheric pressure as 759 mm Hg. What is the final gauge pressure? (3 DECIMALS IN FINAL ANSWER PLS)
A pressure gauge submerged in sea displays 1.6 MPa of absolute pressure. The density of seawater is 1025 kg/m3. At what depth is the pressure gauge situated? Atmospheric pressure is 101,325 kPa
2. A compressed air tank has a volume of 0.85 m3. When the tank is filled with a gauge pressure of 3 bar, determine density of air and weight of air in the tank. Assume temperature of air 15°C. (3 DECIMAL PLACES IN FINAL ANSWER PLS)
A cylinder is filled with 0.4m3 of air at a pressure of 6bar The cylinder is compressed to 0.1 m.3. What is the resulting absolute pressure? Convert p1 to absolute pressure.
A volume of 400 cc of air is measured at a pressure of 740 mm Hg absolute and a temperature of 18 ˚C. What will be the volume (in cc) at 760 mm Hg and 0 ˚C?
At a certain point on the wing of the aircraft, the pressure is 37,803 Pa and the density is 45% of the standard sea level values. Determine the temperature (Kelvin) at that point? Use standard metric units and round off answer to the nearest hundredths.
H.W.1/: The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown in Fig. below. Determine the gage pressure of air in the tank if hl = 0.4 m, h2 = 0.6 m, and h3 = 0.8 m. Take the densities of water, oil, and mercury to be 1000 kg/m³, 850 kg/m³, and 13600 kg/m3, respectively? Oil Air Water IT h2 h3 Mercury
A U-tube manometer uses glycerin as the measuring liquid. What will be the differential pressure in lbf/ft2 if the distance between the levels of glycerin is 103 in?
The absolute pressure in the tank is found to be 1.206 bar. In the measurement of this pressure a U-tube manometer was used. The difference in level was found to be 72,5 cm. The barometric pressure was 72 cm of Determine the specific weight of the liquid used in the manometer. A standard atmospheric pressure = 1.01325 bar.
We have used a tire gauge and measured the air pressure inside a car tire to be 241 kPa. What is the absolute pressure of the air inside the tire, if the car is located in (a) a city located at sea level, (b) a city located in Colorado with an elevation of 1500 m? Express your results in both units of psi and pascals.
A U-tube manometer containing a light oil (specific gravity 0.7) is used to measure the static pressure of air (density 1.2 kg/m³) in a container. If the gauge pressure is 206 N/m², what is the indicated height of oil?
2)What is the maximum gauge pressure of water that can be measured using a piezometer 2.5 m high? almosphere? (Ans. 24.5 kN/m2)