Form the figure shown, a flexible belt placed around a rotating drum of 4-inch radius acts as a brake when the arm ABCD is pulled down by the force P. The coefficient of kinetic friction between the belt and the drum is 0.7. What force P that would result in a braking torque of 400 lb • in., assuming that the drum is rotating counterclockwise. Neglect the weight of the brake arm. 60° . A 2 in 4 in.. B 4 in. +-2 in 60° D

Form the figure shown, a flexible belt placed around a rotating drum of 4-inch radius acts as a brake when the arm ABCD is pulled down by the force P. The coefficient of kinetic friction between the belt and the drum is 0.7. What force P that would result in a braking torque of 400 lb • in., assuming that the drum is rotating counterclockwise. Neglect the weight of the brake arm. 60° . A 2 in 4 in.. B 4 in. +-2 in 60° D

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.60P: The force P applied to the brake handle enables the band brake to reduce the angular speed of a...

See similar textbooks

Similar questions

The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
Form the figure shown, a flexible belt placed around a rotating drum of 4-inch radius acts as a brake when the arm ABCD is pulled down by the force P. The coefficient of kinetic friction between the belt and the drum is 0.7. What force P that would result in a braking torque of 400 lb in., assuming that the drum is rotating counterclockwise. Neglect the weight of the brake arm. 60° B 4 in.. 60° +2 in.- 2 Р
The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the 36° V-pulley is 0.15, and the weight of the han- dle is 15 N. If a force of 200 N is aPplied to the end of the handle, determine the maximum torque for which no mo- tion occurs if the torque is applied Counterclockwise. 150 mm T 200 N 60 150 mmi 675 mm 75 mm
A car has hydraulically operated disc brakes at the front and drum brakes at the rear. The frontbrakes have pistons of 58 mm diameter each, whereas each of the wheel cylinder at the rearbrake has 28 mm diameter. The master cylinder piston has diameter of 40 mm. The brake footpedal has a leverage of 4. If the brake pedal is applied a force of 100 N, Calculate (i) The brakingforce on the front axle, (ii) The braking force on the rear axle.
Please, reaply as soon as posible! Static Problem The band brake shown controls the rotation of the drum. The coefficient of friction between the belt and the drum is 0.25. The weight of the lever is negligible.Determine the force P that must be applied at the end of the braking lever to resist a torque T = 200 lb in, if the torque is applied in the: a) Clockwise b) Counterclockwise direction.
The electric motor shown in Fig. and delivers 50 in. Ib of torque to pulley A of a furnace blower by means of a V-belt. The effective diameters of the 36° pulleys are 5 in. The coefficient of friction is 0.30. De- termine the minimum distance a to prevent slipping of the belt if the rotation of the motor is clockwise. weighs 30 lb 8 in. 20 in.
The figure below shows the essential parts of a hydraulic brake system. The area of the piston in the master cylinder is 1.8 cm² and that of the piston in the brake cylinder is 6.4 cm2. The coefficient of friction between shoe and wheel drum is 0.50. If the wheel has a radius of 37 cm, determine the frictional torque about the axle when a force of 50 N is exerted on the brake pedal. N. m Wheel drum Pedal Shoe Master cylinder cylinder Brake
A flat belt passes over two idler pulleys and under a rotating drumof diameter 8 in. The axle of the drum is free to move vertically ina slot, and a spring keeps the drum in contact with the belt. Whatis the minimum force which should be exerted by the spring if slippageis not to occur when a 30-lb · ft torque is applied to the drum? Thecoefficient of static friction between belt and drum is 0.30 and theangle of contact is 180 degrees.
A differential band brake is used to retard a shaft carrying flywheel weighing 3 kN with radius of gyration350 mm. If the brake drum diameter is 250 mm and coefficient of friction is 0.15, determine thefollowing: (i) the braking torque when an effort of 150 N is applied at the end of the lever, (ii) number ofrevolutions of the flywheel before it comes to rest, and (iii) time taken by the flywheel to come to rest.The drum rotates at 500 rpm in clockwise direction and the layout of the brake is as shown in figure.
The block brake shown below is set by a spring that produces a force S on each arm equal to 682 lb. The wheel diameter is 14 in., and the angle of contact for each block is 110°. Using 0.40 as a value of the coefficient of friction between the drum and lining, determine the maximum torque in foot-pounds that the brake is capable of absorbing. S + S 1/2" 1/2"
The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the 36° V-pulley is 0.15, and the weight of the han- dle is 15 N. If a force of 200 N is applied to the end of the handle, determine the maximum torque for which no mo- tion occurs if the torque is applied Clockwise. 150 mm T 200 N 60 150 mm -675 mm 75 mm
B r P F A UBC Engineering Your team is prototyping a simple braking system for your model car. The 3.4 kg wheel with a radius of r = rad 0.15 m is rotating at w = 18 - .A servo motor can apply a variable force F, which in its first two seconds of operation is equal to F = 10t N and afterwards is equivalent to a constant force of F = 20 N . If the coefficient of kinetic friction between the braking arm and the wheel is μ= 0.2, determine the time needed for the wheel to come to a full stop. The point of contact P between the wheel and the arm is a distance r = -0.2 + 0.26 ĵ m from point A. The force of the servo motor is applied at exactly half of the horizontal distance to A from the point of contact. Assume the wheel can be treated as a disk and that the braking arm is massless. t =