The figure below shows the essential parts of a hydraulic brake system. The area of the piston in the master cylinder is 1.8 cm? and that of the piston in the brake cylinder is 6.4 cm2. The coefficient of friction between shoe and wheel drum is 0.50. If the wheel has a radius of 37 cm, determine the frictional torque about the axle when a force of 50 N is exerted on the brake pedal. N. m Wheel drum Pedal Shoe Master Brake cylinder cylinder

The figure below shows the essential parts of a hydraulic brake system. The area of the piston in the master cylinder is 1.8 cm? and that of the piston in the brake cylinder is 6.4 cm2. The coefficient of friction between shoe and wheel drum is 0.50. If the wheel has a radius of 37 cm, determine the frictional torque about the axle when a force of 50 N is exerted on the brake pedal. N. m Wheel drum Pedal Shoe Master Brake cylinder cylinder

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.56P: The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The...

See similar textbooks

Similar questions

The screw of the carjack has a pitch of 0.1 in. and a mean radius of 0.175 in. Note that the ends of the screw are threaded in opposite directions (right- and left-handed threads). The coefficient of static friction between the threads is 0.08. Calculate the torque C0 that must be applied to the screw in order to start the 1200-1b load moving (a) upward; and (b) downward.
The force P applied to the brake handle enables the band brake to reduce the angular speed of a rotating drum. If the tensile strength of the band is 3800 lb, find the maximum safe value of P and the corresponding braking torque acting on the drum. Assume that the drum is rotating clockwise.
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
Q5: The block brake, as shown, provides a braking torque of 360 N.m The diameter of the brake drum is 300 mm. The coefficient of friction is 0.3. Find 1. the force (P) to be applied at the end of the lever for the clockwise and counter clockwise rotation of the brake drum, and 2. The location of the pivot or fulcrum to make the brake self-locking for the clockwise rotation of the brake dracs 100 10 ( F₁ 4 μ sin 80 20+ sin20 T = (F₁) r Bearing Area A, b(2r sind) RN = (1 20 R 600 Brake drum
The torque transmitted by a single block brake is 70 N-m. The coefficient of friction between the drum and the lining is 0.35. The drum diameter is 240 mm. Which of the following is the normal force RN pressing the block on the brake block on the wheel? 200 200 4 TEL 200 N 560 N 1600 N 1450 N
Please, reaply as soon as posible! Static Problem The band brake shown controls the rotation of the drum. The coefficient of friction between the belt and the drum is 0.25. The weight of the lever is negligible.Determine the force P that must be applied at the end of the braking lever to resist a torque T = 200 lb in, if the torque is applied in the: a) Clockwise b) Counterclockwise direction.
The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the 36° V-pulley is 0.15, and the weight of the han- dle is 15 N. If a force of 200 N is applied to the end of the handle, determine the maximum torque for which no mo- tion occurs if the torque is applied Clockwise. 150 mm T 200 N 60 150 mm -675 mm 75 mm
The block brake shown below is set by a spring that produces a force S on each arm equal to 682 lb. The wheel diameter is 14 in., and the angle of contact for each block is 110°. Using 0.40 as a value of the coefficient of friction between the drum and lining, determine the maximum torque in foot-pounds that the brake is capable of absorbing. S + S 1/2" 1/2"
The mass center of the rear-engine 1530-Kg car is at G. The coefficient of static friction is 0.5 at driving tire/road interfaces. 600'mm 1500 1500 mm mm
The band of a brake has a contact angle of 18° deg. If the pulls on the bands are 275 kg and 100 kg, find the coefficient of friction.
A band brake embraces a 500 mm diameter drum with an angle of lap of 270° and produces a braking torque of 200 Nm. The coefficient of friction is 0.2. One end of the band is attached to the fulcrum pin and the other end is attached to a pin B. Which of the following is the tension in the slack side of the band? 75 -450 C 270° O 280 N O 510N O 255 N 0 445 N All dimensions in mm.