For the assembly shown in the figure, a force of 25 kN is applied to the ring at F. Determine the deformation incurred by rod CD. Also, calculate the angle of tilt in radians for bar AC and the horizontal displacement of point F. Use E = 120 GPa. 0.9 m ACD=500 mm² 0.6 m 25 kN AAB 850 mm² 1.5 m B 0.3 m² 0.2mA=

For the assembly shown in the figure, a force of 25 kN is applied to the ring at F. Determine the deformation incurred by rod CD. Also, calculate the angle of tilt in radians for bar AC and the horizontal displacement of point F. Use E = 120 GPa. 0.9 m ACD=500 mm² 0.6 m 25 kN AAB 850 mm² 1.5 m B 0.3 m² 0.2mA=

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Using Conjugate-Beam Method, determine the displacement at B. 12 m I 80 KN B E = constant = 200 GPa I=600 (106) mm² 12 m 21
4m 100KN 5m AZ The structure is composed of bar AB and a semi secular arc as shown in the figure. It is fixed at the lower and a 100 kN load is applied at the free end. Using E = 200 GPa, I = 1000x1066 mm4. Calculate the Horizontal displacement of the point where the load is applied. (mm) The structure is composed of bar AB and a semi secular arc as shown in the figure. It is fixed at the lower and a 100 kN load is applied at the free end. Using E = 200 GPa, I =1000x1066 mm4. Calculate the Vertical displacement of the point where the load is applied. (mm)
For the assembly shown in the figure, a force of 25 kN is applied to the ring at F. Determine the deformation incurred by rod CD. Also, calculate the angle of tilt in radians for bar AC and the horizontal displacement of point F. Use E = 120 GPa
A beam is subjected to a uniform force w as shown in the figure below. The E of the entire section is 200 GPa, and the I is 60×10^6 mm^4. Try to draw the beam’s Shear Curve and Moment Curve.(a) If point C supports sink 0.1 m before assembly(b) If the uniform force w is removed and the point C sinks, but the point A support is rotated 0.005 rad clockwise before assembly
A statically indeterminate truss is shown in Figure 4b. Support at A is a pin and E is a roller. The applied load at C is P = 8 kN. Assume, cross sectional area of each bar, A = 600 mm2 and modulus of elasticity, E = 200 GPa. Use virtual work method to determine the vertical displacement at C. D 4m A B C 10 kN P 3m 3m Figure 4b
F 26 11/1/2 C + S 2 B A solid bar S (E-200 GPa, A=100 mm²) is attached to a cantilever beam (E=200 GPa, 1=250*106 mm) as shown in the figure. Calculate the force S in the bar due to an applied force F=100 kN at the free end of the cantilever. Disregard axial deformations of the beam. a=30°, L=4m
10.Determine the vertical displacement of joint C of the truss. Each member has a cross-sectional area of A = 300 mm² and E = 200 GPa. Use the method of virtual work. H 3 m B E 4 m D - 4 m 4 m 4 m 3 kN 3 kN 4 kN Figure Q10
-211. The rigid bars shown in the figure are separated by a roller at C and pinned at A and D. a steel rod at B helps support the load of 50KN. Compute he vertical displacement of the roller at C. L=3m A=300mm? 50KN E=200GPA 2m 2m D 3m 1.5m A В
Shear force acting on section H in the figure Shear stress y when T = 50 kN acts Draw the distribution of zy.
ЗР L/6 1. From figure 1.1. Determine 10 the distance 'a' as a fraction of the beam's length 'L' for locating the roller support at C so that the internal moment at B is zero. * 2. A particle is subjected to vector forces A = (2lb)i + (-6lb)j + (10lb)k and B = (-6lb)i %3D + (-2lb)j + (2lb)k. What will be the resultant force? *
Compute the vertical displacement of joints B and C for the frame shown in the figure. Given: /= 360 in.“, E= 30,000 kips/in.2, and P= 14 kips. Consider only flexural deformations. A В 6' 7'- 8'- P The magnitude of the vertical component of displacement at Cis ocv= in. The magnitude of the vertical component of displacement at B is õBV= in.
3. Rigid member ABD is connected to elastic member CDE as shown. For the given loading, what are the vertical displacements of points A and E? A 20KN dimensions in meters B rigid I ст 0.4 E 0.2 5kN E=7oGPa A=100mm²