Define an equipment grounding conductor. The conductive path that part. of eftective an graund-fault Current path and connects normally nen-current- carrying metal parts ot. and electrode Chapter 6 cquipment together grounded conductor or to the grounding bo th. to the system conductor Or 18. Circuit Al supplies GFCI receptacles O and ®. Circuit A2 supplies GFCI receptacles (3 and O. Receptacles O and O are feed-through type. Using colored pencils or mark- ing pens, complete all connections.

Define an equipment grounding conductor. The conductive path that part. of eftective an graund-fault Current path and connects normally nen-current- carrying metal parts ot. and electrode Chapter 6 cquipment together grounded conductor or to the grounding bo th. to the system conductor Or 18. Circuit Al supplies GFCI receptacles O and ®. Circuit A2 supplies GFCI receptacles (3 and O. Receptacles O and O are feed-through type. Using colored pencils or mark- ing pens, complete all connections.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter20: Special-purpose Outlets For Ranges, Counter-mounted Cooking Unit , And Wall-mounted Oven

Section20.2: Wall-mounted Oven Circuit And Free-standing Range

Problem 12R

See similar textbooks

Similar questions

c.1. Which of the following is one of the three essential functions of an equipment grounding conductor?A. Provide an arc-fault current pathB. Establish groundingC. Establish bondingD. Ensure the system is groundedc.2. What's another name for the three-point method of Earth resistance testing?A. Fall-of-potentialB. Line surgeC. Spatial shieldingD. Leakage current c.3. If the National Electrical Code provides a requirement to ground equipment, it generally implies thatthere will be a direct connection to the Earth of a connection through a/anA. grounding electrode conductor.B. equipment grounding conductor.C. equipotential bonding conductor.D. bonding conductor.
7.B. The size of a grounding electrode conductor for a service or separately derived system is generally basedon the size of the largestA. ungrounded supply conductor.B. equipment grounding conductor.C. grounded electrode.D. bonding jumper.7.C. Which of the following statements about bonding is true?A. The joint or termination must offer opposition in the circuit for effective electrical connections.B. Effective bonding keeps impedance high if a fault should occur.C. The entire electrical safety circuit is only as good as its strongest bonded link.D. Bonding connections must endure high levels of fault current until overcurrent protective devices can operate.
Most residential general lighting circuits are wired with 14-AWG copper conductors and are protected by 15-amp circuit breakers. However, there are many electricians who install 12-AWG copper conductors and protect them with 20-amp circuit breakers. How will you know which conductor size and which circuit breaker size will be used for the general lighting branch circuits in the house you are wiring?
What is the minimum trade size PVC conduit to contain 201 #12AWG TW75 Copper conductors.
Which of the following Surge Diverter use non-linear resistances in its fabrication? Rod - Gape SD. Lightning Arrester SD. Expulsion Tube SD. O All of the above.
Write in Briefly about circuit breaker, current transformer and voltage transformer
Calculate the following. a) Expected voltage at “A” with switch SW1 open. b) Expected voltage at “A” with switch SW1 closed.
Consider a 5A ammeter is connected to the secondary side of a 100/5A current transformer (CT) in order to measure the current of the circuit. Safety considerations require that the CT has to be short circuited (or the primary circuit switched off) during a replacement of the ammeter. Explain why this is needed.
9. Which grounding method is typically required of higher-voltage systems? A. Grounding through inductorsB. Grounding through a low amount of resistanceC. Grounding through a high-impedance device D. Grounding through surge arresters 10. Which term relates to the conductors connected to the output side of a separately derived system? A. Neutral conductorB. Transformer secondary conductorC. System conductor D. Derived phased conductor 11. If there's no service disconnect at a remotely supplied building, then the grounding electrode conductor and the equipment grounding conductor can be bonded together at a A. junction box.B. structural steel location. C. grounding electrode rod. D. water line. 12. In a DC system, the bonding jumper between the negative of the supply and ground is normally made at the source or at the A. first disconnecting means. B. first device on the supply. C. end of the DC line.D. entrance to the building. 13. Which of the following is a common raceway…
Find the maximum distance between outlets when using #10 Cu THWN copper wire at 240V on a 20A single phase load w/o exceeding a 3 percent voltage drop. What is considered the maximum. permissible drop for feeders and branch circuits per the NEC recommendation?
18. If the current flowing in an operating circuit must be approximately measured without interrupting the current, which of the following through-type current transformers would you recommend? A. Bar-type B. Plain-through-type C.Split-core-type D. Bushing-type
3. The three bus-bar conductors in an outdoor sub-station are supplied by units ofpost insulators. Each unit consists of a stack of 3-pin insulators fixed one on the top of the other. The voltage across the lowest insulator is 8-45 kV and that across the next is 7-25 kV. Find the bus-bar voltage of the station. [38-8 kV]