. The three bus-bar conductors in an outdoor sub-station are supplied by units of post insulators. Each unit consists of a stack of 3-pin insulators fixed one on the top of the other. The voltage across the lowest insulator is 8-45 kV and that across the next is 7-25 kV. Find the bus-bar voltage of the station.

. The three bus-bar conductors in an outdoor sub-station are supplied by units of post insulators. Each unit consists of a stack of 3-pin insulators fixed one on the top of the other. The voltage across the lowest insulator is 8-45 kV and that across the next is 7-25 kV. Find the bus-bar voltage of the station.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter20: Special-purpose Outlets For Ranges, Counter-mounted Cooking Unit , And Wall-mounted Oven

Section20.2: Wall-mounted Oven Circuit And Free-standing Range

Problem 12R

See similar textbooks

Similar questions

The three bus-bar conductors in an outdoor sub-station are supplied by units of post insulators. Each unit consists of a stack of 3-pin insulators fixed one on the top of the other. The voltage across the lowest insulator is 8-45 kV and that across the next is 7-25 kV. Find the bus-bar voltage of the station.
Most residential general lighting circuits are wired with 14-AWG copper conductors and are protected by 15-amp circuit breakers. However, there are many electricians who install 12-AWG copper conductors and protect them with 20-amp circuit breakers. How will you know which conductor size and which circuit breaker size will be used for the general lighting branch circuits in the house you are wiring?
h.1. In an alternating-current system, the maximum size for a copper grounding electrode conductor isA. 250 kcmil.B. 3/0.C. 500 kcmil.D. 4/0. h.2. The figure shows a fault condition in an ungrounded electrical system. Which of the following will occurbecause of the fault in this system?A. Only the overcurrent protector at Point A will trip open.B. The ground fault will heavily damage the service.C. Nothing will happen until a second ground fault occurs.D. The overcurrent protection will trip, shutting off all the line side power.
3. The zero sequence current is times the current in neutral wire.
In an outdoor substation the three bus-bar conductors are supported by units of post type insulators. Each unit consists of a stack of 3 pin type insulators fixed one on the top of the other. The voltage across the lowest insulator is 13kV and that across the next unit is 12KV. Estimate: 17. i. ratio of mutual to self-capacitance ii. the bus-bar voltage of the substation. iii. Efficiency across the string of insulators
Load in Figure 1 needs to be connected to Mains Switch Board (MSB) using multicore PVC cable. As a maintenance engineer, you need to proposed cable size for the load, Determine the following issues. 1) Calculate current demand for the circuit. 1) Detemine suitable MCCB (Model and nominal current rating) should be used to protect the load against over-current. im Propose suitable cable size for the load in Figure 1. iv) Calculate voltage drop of the proposed cable WITHOUT consider the cable reactance and voltage drop correction due to higher cable operating temperature v) Calculate voltage drop of the proposed cable BY consider the cable reactance and voltage drop correction due to higher cable operatıng temperature vi) If the multicore PVC eable is change into 3 single core PVC cables, what the suitable cable size. All other multicore cables not available. (25 + variable x) m (A) 30 m (B) (15 + variable b) m (C) Multicore PVC cable MCCB 95 kW. (400 + variable y) V. 0.85 p.f. Load MSB…
12 - Due to the effect of the resistance of the cable connected to RTD, two-wire cables up to ……. meters and three-wire cables up to ……... meters are used in standard designs. A) 10-150B) 40-500C) 50-195D) 30-230E) 200-1000
8. Parallel conductors must be installed in sizes no smaller thanA. 1/0.B. 2/0.C. 750 kcmil.D. 4/0.
Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material consists of two layers. The thickness of each layer is 2 cm. The voltage of first and second layers are 20 kV, 5 kV respectively. The maximum Electric stress of the cable is
c.1. Which of the following is one of the three essential functions of an equipment grounding conductor?A. Provide an arc-fault current pathB. Establish groundingC. Establish bondingD. Ensure the system is groundedc.2. What's another name for the three-point method of Earth resistance testing?A. Fall-of-potentialB. Line surgeC. Spatial shieldingD. Leakage current c.3. If the National Electrical Code provides a requirement to ground equipment, it generally implies thatthere will be a direct connection to the Earth of a connection through a/anA. grounding electrode conductor.B. equipment grounding conductor.C. equipotential bonding conductor.D. bonding conductor.
Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material consists of two layers. The thickness of each layer is 2 cm. The voltage of first and second layers are 20 kV, 5 kV respectively. The minimum Electric stress of the cable is
A set of conductors is used to supply residential unit with a total load current of 60 A at a single-phase supply voltage of 230 V. What would be the minimum size of the conductor to be used to achieve at least 5% voltage drop? The total conductor length is 300 ft. ..