Calibrate a vertical cylindrical container medium water inside container, density is 1000 kg/m³. Assume temperature of water is constant, from start of filling up to full of a container. Plot a curve between weight of water in a container when filled (ordinates) and for every 1 cm in height. (Use the following steps as above in calibrating tank.)

Calibrate a vertical cylindrical container medium water inside container, density is 1000 kg/m³. Assume temperature of water is constant, from start of filling up to full of a container. Plot a curve between weight of water in a container when filled (ordinates) and for every 1 cm in height. (Use the following steps as above in calibrating tank.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. In Buckingham n thearem, if n is the number of variables and m is the number of basic dimensions, the number of independent dimensionless parameters would be, A. (m-n) B. (n - m) C. (m + n) D. (n/m) 2. Which is a dimensionless parameter? A. Froude Number B. Angular Velacity c. Viscosity D. Density
In Figure below all fluids are at 20 deg.C. Determine pressure at point B, if pressure at point A is 150 kPa and weight of air is neglected. Use the table below for the densities at 20 deg.C. Liquid p. kg/m Kerosene - Ammonia 608 Benzene 881 Air Carbon tetrachloride 1590 Benzene Ethanol 789 Ethylene glycol Freon 12 B 1117 40 cm 9 cm 1327 20 cm Gasoline 680 14 cm Glycerin Kerosene 1260 t8 cm 804 Mercury- Water Mercury Methanol 13,550 791 SAE 10W oil 870 SAE 10W30 oil 876 SAE 30W oil 891 SAE 50W oil 902 Water 998 Seawater (30%e) 1025
1. A special-purpose piece of laboratory glassware, called a pyncnometer; is used to measureLiquid densities. It has a volume of 25 cc, and a mass of 17 .24 g when it is full of air. Whenfilled with a liquid of unknown density, its mass = 45.00 g. What is the density of this liquid?How large an error do we make if we ignore the mass of the air that was in it when we weighed itand found m = 17.24 g?
Time left 1:5 An ideal gas has its pressure (1.8) times and mass density (2.2) times increased. If the initial temperature is 265.4 °C, what is the final temperature in °C, and use one number after the decimal (xxx.x)? Answer: NEXT PAGE pe here to search DELL
A tank is 6 m long, 4 m wide, 5 m high, and contains kerosene with density 820 kg/m³ to a depth of 4.5 m. (Use 9.8 m/s² for the acceleration due to gravity.) (a) Find the hydrostatic pressure (in Pa) on the bottom of the tank. 36162 Pa (b) Find the hydrostatic force (in N) on the bottom of the tank. 867888 N (c) Find the hydrostatic force (in N) on one end of the tank. N
PLEASE SHOW SOLUION STEP BY STEP WITH UNITS. PLEASE ANSWER IT IN 30 MINS. TOPIC: THERMODYNAMICS - PROCESSES OF GASES
The pressure difference between 2 points is 100,000 Pascals of a fluid column with height of 4 meters. The specific gravity of the fluid is closest to what value? The answer has a margin of 0.05 from the exact answer.
. I am planning to perform some volume-flow rate measurements in the Fluid Mechanics Laboratory. For this, I need a volumetric measuring tank (graduated cylinder) and a stopwatch. I considered the volume of the measured tank as 15 gallons and a stopwatch with reaction time as 1/10th of a second (though resolution of 1/1000th of a second). What is the volume flow rate if it takes 5 minutes to fill a 15-gallon of tank? Determine the smallest division to be on the tank in order to estimate the volume flow rate within an accuracy of ± 0.05 gpm.
The dynamic coefficient of viscosity m (viscosity of a fluid) is from, where v= velocity, d = distance, F = Force and A = area. Find the dimensions of m.
b) The following shear stress – shear rate behavior was observed. Shear rate (Seconds-1) Shear Stress (dynes/cm?) 20 11 30 15.2 40 19.1 50 22.9 60 26.5 1. Make a plot of shear stress (ordinate) vs shear rate (abscissa) on log-log paper. 2. Can the fluid behavior be accurately modeled by the Newtonian, Bingham plastic, or Power law model?
Water X 50-mm inside diameter The volume flow rate of the system The pressure at the point "A" The pressure at the point "B" 25-mm diameter As a consultant at one of the country's leading soft drink companies, you are tasked with evaluating the system depicted to determine the following parameters using Bernoulli's Equation if the values assigned to "X" and "Y" are 3m and 0.5m respectively: i. ii. iii.
Assignment 3 On Viscosity Calculation - Word TOUT REFERENCES MAILINGS REVIEW VIEW Hyperlink P Bookmark tArt Chart Screenshot Apps for Office Online Video Cross-reference Comment Header Footer Page Number Text Quick WordA Box Parts - ns Apps Media Links Comments Header & Footer (2) Referring to the following figure, the distance between plates is Ay = 0.5 cm, Av: = 10 cm/s, and the fluid is ethanol at 273 K having a viscosity of 1.77cp (0.0177 g/cm s). (a) Calculate the shear stress ty and the velocity (b) gradient of shear rate -/dy using cgs units. (c) Repeat using SI units. A Torce Fdshear berween teoparailel plates