A cantilever is to be attached to the flat side of a 6-in wide channel used as a column. The cantilever is to carry a load as shown in the figure. If two fasteners are used, should the array be arranged vertically, horizontally, or diagonally? How would you decide? Specify an optimal bolt pattern and size the bolts. 6 in 6 in -in steel plate 6 in- + 2000 lbf

A cantilever is to be attached to the flat side of a 6-in wide channel used as a column. The cantilever is to carry a load as shown in the figure. If two fasteners are used, should the array be arranged vertically, horizontally, or diagonally? How would you decide? Specify an optimal bolt pattern and size the bolts. 6 in 6 in -in steel plate 6 in- + 2000 lbf

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter40: Drive Axles And Differentials

Section: Chapter Questions

Problem 8RQ: The double-offset joint is typically used in applica tions that require______. a. higher operating...

See similar textbooks

Similar questions

-.3: Draw the front view for a square-headed bolt and a square neck with a castle nut and a washer in position. Take the bolt diameter is 24mm and length is 100mm.(use ISO metric threads) Your answer •ns: Draw the two views (front and top) of a two plates (thickness 5 mm) joined by a single riveted , double strap butt joint. use a Round top countersunk head for the rivet( see Figure). The curve of the head R=1.0606*d 1.5 d 0.2 d 0.25 d
Two 1/4 in × 8 in A36 steel plates are joined with a lap joint using 3/4 in A325-N bolts. If a concentric unfactored live load of 50 kips (dead load = 0) is required to be resisted by the connection and the bolt shear strength controls the design, the minimum required number of bolts is?
As shown in figure below, two plates are clamped by washer-faced 2 in-20 UNF SAE grade 5 bolts each with a standard 2 N steel plain washer. The top plate is steel and the bottom pplate is gray cast iron. If a total of 8 bolts where used to close 1 feet diameter pipe which applied at maximum pressure of 150 psi. Calculate the static and fatigue safety factor of this joint. Used Goodman theory for tha fatigue safety 1/2 factor. 3/4
QUESTION: Suppose a bolted tension used in a doube-D ring configuration is properly preloaded. The spring constant for the bolts is 7.8 MN/m and the spring constant for the members is 12.7 MN/m. By how much does the tensile force in the bolt increase when a load of 705 N is applied? You may assume that joint separation does not occur. Give your answer in units of N
M16 x 2.0 ISO 5.8 coarse series bolts and nuts clamp a 26-mm-thick steel cover plate to a 6-mm-thick steel flange. Steel washers (Size: 16R) are used under the head of the bolt and also under the nut . Assume E = 207 GPa- (a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness. (c) Determine the stiffness of the members. (d) Determine the stiffness of the joint.
Q1:Prepare a full-section assembly drawing of the four fastener assemblies shown in the Figure. Dimension both the clearance and the threaded holes. A top view may be shown if required. Scale 1: 1. .250-20 FHMS .375 HEX BOLT AND NUT THREADED INTO BASE 1.00 ↓ .50 T 2.00 Ø.375 STUD THREADED .312 HEX X 1.25 LG INTO BASE FOR 1.00 IN. CAP SCREW AND WITH HEX NUT AND LOCK WASHER ON SPOTFACE SURFACE PLATE WASHER A 2.00- -2.00 -1.00- BASE 1.00- .25 1.50
Problem 3: A Hexagonal bolt connects two members. The joint has a gap 1 = 2 in and the applied load is 2000 lb. Both of the clamped parts are steel. A preload of 90% the bolt's proof strength will be applied first. For this design, an SAE grade 1, 5/16"-18 UNC-2A bolt is chosen made from A307 with rolled threads. Washers are included between the head and the joint, and between the nut and the joint. Determine a suitable length for the bolt? Find its safety factor against yielding and against joint separation. Are these values acceptable?
Repeat question but with the load at joint 1 acting horizontally?
D Problem Number A B C D E F N (d) Calculate the connection / joint stiffness. (e) Calculate the bolt stiffness. Ps Bolt grade Bolt spec. (a) Determine the force on the end plate. (b) Calculate the nominal force per bolt w/o preload. (c) Calculate the nominal stress in the bolt w/o preload. 8-34 An end plate is loaded by the gas pressure inside a pipe. N is the total number of bolts. Assume the pipe / plate material is ASTM A36 steel. The bolts are 2.0 inches long with a threaded length of 1.25 inches. The nut thickness is 0.50 inches. For the data specified in column 8-34: in 3.5 in 4.25 in 6 in 8 in 10 1500 psi SAE 5 in-13 (f) Assuming safety factor of Q = 1.25 for the connection, calculate the required bolt preload. (g) Calculate the maximum force in the bolt. (h) Calculate the maximum stress in the bolt. (i) Calculate the torque required to establish the bolt preload.
Use LRFD and design a 13-foot-long tension member and its connection for a service dead load of 8 kips and a service live load of 24 kips. No slip of the connection is permitted. The connection will be to a 3⁄8-inch-thick gusset plate, as shown in Figure . Use a single angle for the tension member. Use Group A bolts and A572 Grade 50 steel for both the tension member and the gusset plate.
For a bolted assembly with six bolts, the stiffness of each bolt is kb = 2.8 Mlbf/in and the stiffness of the members is km= 14 Mlbf/in per bolt. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. Assume the bolts are preloaded to 75 percent of the proof load. Determine the yielding factor of safety. The yielding factor of safety is
3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all ~0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.