5. A 300.0 mg sample containing Na¿CO3, NaHCO, and NaOH and inert material either alone or in some combination was dissolved and titrated with 0.1000 M HCI the titration required 24.41 ml to reach the phenolphthalein endpoint. And an additional 8.67 mL to reach the methyl red endpoint. Determine the composition of the sample and calculate the percent of each titrated component.

5. A 300.0 mg sample containing Na¿CO3, NaHCO, and NaOH and inert material either alone or in some combination was dissolved and titrated with 0.1000 M HCI the titration required 24.41 ml to reach the phenolphthalein endpoint. And an additional 8.67 mL to reach the methyl red endpoint. Determine the composition of the sample and calculate the percent of each titrated component.

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter21: Potentiometry

Section: Chapter Questions

Problem 21.22QAP

See similar textbooks

Similar questions

A 0.2481 M solution of KOH is used to titrate 30.00 mL of 0.269 M hydrobromic acid. Assume that volumes are additive. (a) Write a balanced net ionic equation for the reaction that takes place during the titration. (b) What are the species present at the equivalence point? (c) What volume of KOH is required to reach the equivalence point? (d) What is the pH of the solution 1. before any KOH is added? 2. halfway to the equivalence point? 3. at the equivalence point?
Without doing detailed calculations, sketch the curve for the titration of 30.0 mL of 0.10 M NaOH with 0.10 M HCl. Indicate the approximate pH at the beginning of the titration and at the equivalence point. What is the total solution volume at the equivalence point?
Fifty cm3 of 1.000 M nitrous acid is titrated with 0.850 M NaOH. What is the pH of the solution (a) before any NaOH is added? (b) at half-neutralization? (c) at the equivalence point? (d) when 0.10 mL less than the volume of NaOH to reach the equivalence point is added? (e) when 0.10 mL more than the volume of NaOH to reach the equivalence point is added? (f) Use your data to construct a plot similar to that shown in Figure 14.10 (pH versus volume NaOH added).
Without doing detailed calculations, sketch the curve for the titration of 50 mL of 0.050 M pyridine, C6H5N (a weak base), with 0.10 M HCl. Indicate the approximate pH at the beginning of the titration and at the equivalence point. What is the total solution volume at the equivalence point?
A buffer is prepared by dissolving 0.062 mol of sodium fluoride in 127 mL of 0.0399 M hydrofluoric acid. Assume no volume change after NaF is added. Calculate the pH of this buffer.
A 0.3012g sample of an unknown monoprotic acid requires 24.13mL of 0.0944MNaOH for neutralization to a phenolphthalein end point. There are 0.32mL of 0.0997MHCl used for back titration. a. How many moles of OH are used? How many moles of H+ from HCl? _______moles OH ________moles H+ b. How many moles of H+ are there in the solid acid? Use Eq.5. ____________ moles H+ in solid c. What is the molar mass of the unknown acid? Use Eq.4. ____________ g/mol
A 65.0-mL sample of 0.010 M Pb(NO3)2 was added to a beaker containing 40.0 mL of 0.035 M KCl. Will a precipitate form?
Malonic acid (HO2CCH2CO2H) is a diprotic acid. In the titration of malonic acid w ith NaOH, stoichiometric points occur at pH = 3.9 and 8.8. A 25.00-mL sample of malonic acid of unknown concentration is titrated with 0.0984 M NaOH, requiring 31.50 mL of the NaOH solution to reach the phenolphthalein end point. Calculate the concentration of the initial malonic acid solution. (Sec Exercise 113.)
If 55 mg of lead(II) sulfate is placed in 250 mL of pure water, does all of it dissolve? If not, how much dissolves?