4.3 (A). A conveyor beam has the cross-section shown in Fig. 4.24 and it is subjected to a bending moment in the plane YY. Determine the maximum permissible bending moment which can be applied to the beam (a) for bottom flange in tension, and (b) for bottom flange in compression, if the safe stresses for the material in tension and compression are 30 MN/m2 and 150 MN/m² respectively. [32.3, 84.8 kN m.] ŷ ? 25 150 InA ? All dimensions in mm 100 -50--50-j-50+

4.3 (A). A conveyor beam has the cross-section shown in Fig. 4.24 and it is subjected to a bending moment in the plane YY. Determine the maximum permissible bending moment which can be applied to the beam (a) for bottom flange in tension, and (b) for bottom flange in compression, if the safe stresses for the material in tension and compression are 30 MN/m2 and 150 MN/m² respectively. [32.3, 84.8 kN m.] ŷ ? 25 150 InA ? All dimensions in mm 100 -50--50-j-50+

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A conveyor beam has the cross-section shown in Fig. 4.24 and it is subjected to a bending moment in the plane YY. Determine the maximum permissible bending moment which can be applied to the beam (a) for bottom flange in tension, and (b) for bottom flange in compression, if the safe stresses for the material in tension and compression are 30 MN/m2 and 150 MN/m' respectively. A conveyor beam has the cross-section shown in Fig. 4.24 and it is subjected to a bending moment in the plane YY. Determine the maximum permissible bending moment which can be applied to the beam (a) for bottom flange in tension, and ( b) for bottom flange in compression, if the safe stresses for the material in tension and compression are 30 MN/m2 and 150 MN/m' respectively. Can I get the solution for A and B.. Thanks! Subject: Strengh of Materials
The cantilever beam in Fig. (a) carries a triangular load, the intensity of which varies from zero at the left end to 360 lb/ft at the right end. In addition, a 1000-lb upward vertical load acts at the free end of the beam. (1) Derive the shear force and bending moment equations, and (2) draw the shear force and bending moment diagrams. Neglect the weight of the beam
2. A simply supported rectangular concrete beam of span 8m has to be prestressed with a force of 1600 kN. The tendon is of parabolic profile having zero eccentricity at the supports. The beam has to carry an external uniformly distributed load of intensity 30 kN/m. Neglecting the self- weight of the beam, the maximum dip (in meters, up to two decimal places) of the tendon at the mid-span to balance the external load should be? Span of the beam, L = 8m Prestressing force, P = 1600 kN %3D U.D.L. on the beam, w = 30 kN/m Maximum dip of tendon to balance the external load e = ?
Problem 4.30 While the stiffness of an elastic cord can be quite constant (i.e., the force versus displace- ment curve is a straight line) over a large range of stretch, as a bungee cord is stretched, it softens; that is, the cord tends to get less stiff as it gets longer. Assuming a soften- ing force-displacement relation of the form k8 - B83, where 8 (measured in ft) is the displacement of the cord from its unstretched length, considering a bungee cord whose unstretched length is 150 ft, and letting k = 2.58 lb/ft, determine the value of the con- stant B such that a bungee jumper weighing 170 lb and starting from rest gets to the bottom of a 400 ft tower with zero speed.
Q3/ Fig. 3 shows a cost iron bracket of cross-section of I-form. Determine the maximum bending moment that should be imposed on this section if the tensile stress in the top flange is not to exceed 40 MN/m² What is then the value of the compressive stress in the bottom flange? Fig. 3 40 mm 200 mm mm 200 mm T 40 mm 120 mm
Q4.A cantilever beam, 50 mm wide by 150 mm high and 6 m long, carries a load that varies uniformly from zero at the free end to 1000 N/m at the wall. (a) Compute the magnitude and location of the maximum flexural stress. (b) Determine the type and magnitude of the stress in a fiber 20 mm from the top of the beam at a section 2 m from the free end. 1/3 x 1000 N/m 6 m
A 5.0-m-long simply supported timber beam carries two concentrated loads as shown. The cross-sectional dimensions of the beam are also shown. Assume L1 = 1.0 m, L2 = 2.0m, P = 12 kN, Q = 31 kN, a = 135 mm, b = 150 mm, c = 90 mm, and d = 445 mm. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the 5.0-m span length. (d) Determine the maximum compression bending stress that occurs in the beam at any location within the 5.0-m span length. a H d В D K
The beam shown in (Figure 1) weighs 320 lb/ft . Determine the magnitude of the internal normal force at point C. Determine the magnitude of the internal shear force at point C. Determine the magnitude of the internal moment at point C.
Fig. (6)
3.11 A beam, 12 m long, is to be simply supported at 2 m from each end and to carry a u.d.1. of 30 kN/m together with a 30 kN point load at the right-hand end. For ease transportation of the beam is to be jointed in two places, one joint being situated 5 m from the left-hand end. What load (to the nearest kN) must be applied to the left-hand end to ensure that there is no B.M. at the joint (the joint is to be a point of contraflexure)? What will be the best position on the beam for the other joint? Determine the position and magnitude of the maximum B.M. present on the beam. [114 kN, 1.6 m from r.h. reaction; 4.7 m from 1.h. reaction; 43.35 kN m]
A rectangular beam of 100 mm wide is subjected to maximum shear force of 50 kN, the corresponding maximum shear stress being 3 N/mm?. The depth of the beam is equal to
A simply supported beam, 50mm wide by 100mm high and 300 mm long is subjected to a concentrated load of 3000 N at a point 100 mm from one of the supports. Draw the shear force and bending moment diagrams for the beam.