Q3/ Fig. 3 shows a cost iron bracket of cross-section of I-form. Determine the maximum bending moment that should be imposed on this section if the tensile stress in the top flange is not to exceed 40 MN/m² What is then the value of the compressive stress in the bottom flange? Fig. 3 40 mm 200 mm mm 40 mm 120 mm

Q3/ Fig. 3 shows a cost iron bracket of cross-section of I-form. Determine the maximum bending moment that should be imposed on this section if the tensile stress in the top flange is not to exceed 40 MN/m² What is then the value of the compressive stress in the bottom flange? Fig. 3 40 mm 200 mm mm 40 mm 120 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer p1 and Part 2: Determine the shear force acting at each of the following locations:(a) x = 11.0- ft (i.e., just to the left of point B)(b) x = 11.0+ ft (i.e., just to the right of point B)(c) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.Answers: a) V = ____ kips b) V = ____ kips c) V = ____ kips Part 3: Determine the bending moment acting at each of the following locations:(a) x = 11.0 ft (i.e., at point B)(b) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2. Answers: a) M = ____ kips-ft b) M = ____ kips-ft Part 4: Use your shear-force and bending-moment diagrams to determine the maximum bending moment, Mmax, and its location, xmax. Use the bending-moment sign convention detailed in Section 7.2.Answers: Mmax = ____ kips-ft xmax = ____ ft
A steel rod is stretched between two walls. At 20C, the tensile force in the rod is 5000N. If the stress is not to exceed 130MPa at -20C, find the minimum allowable diameter of the rod. Use a=11.17x10^-6C and E=200GPa. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong. -Show complete solution and explanation
A steel rod is stretched between two walls. At 20C, the tensile force in the rod is 5000N. If the stress is not to exceed 130MPa at -20C, find the minimum allowable diameter of the rod. Use a=11.17x10^-6C and E=200GPa. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong. -Show complete solution and explanation
A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and 3 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 50 kips tension in the x direction, 65 kips compression in the y direction, and 55 kips tension in the z direction. If v = 0.30 and E = 29 x 10° psi. What is the total elongation in the x-direction?
Question 1.Spiral spring was used to design a mechanical clock. The spring is made of a flat strip 6 mm wide and 0.25 mm thick. The length of the strip is 2.5 m. Assuming the maximum stress of 800 MPa to occur at the point of greatest bending moment. Take E = 200 kN/mm2.(a) Calculate the bending moment.(b) The number of turns to wind up the spring.(c) The strain energy stored in the spring. Question 2A helical compression spring is wound using 2.5 mm diameter music wire. The spring has an outside diameter of 31 mm with plain ground ends, and 14 total coils.a) Estimate the spring rate.b) What force is needed to compress this spring to closure?c) What should the free length be to ensure that when the spring is compressed solid the torsional stress does not exceed the yield strength?d) Is there a possibility that the spring might buckle in service? Question 3A helical compression spring with square and ground ends has an outside diameter of 14 mm, 20 total coils, a wire diameter of 2 mm,…
A circular rod of length 18 cm and diameter 5 mm is made of grade 1045 grade steel. a. Calculate the stress and strain in the rod, and its extension, when it is subjected to 7 kN of tension. (Express your answers using three significant figures.) |MPa E = x10-4 (Express your answer using whole numbers.) AL = | pm b. At what force would the rod begin to yield? (Express your answer using three significant figures.) F = |kN c. By what amount would the rod have to be stretched beyond its original length in order to yield? (Express your answer using whole numbers.) AL = um
A bar is subjected to fluctuating tensile load from 20 kN to 100 kN. The material has yield strength of 240 MPa and endurance limit in reversed bending is 160 MPa. According to the Soderberg principle, the area of cross-section in mm? of the bar for a factor of safety of 2 is
Solve for the force in BD, vertical reaction at point C, horizontal reaction at point C, resultant of reaction at point C. What is the allowable tensile (normal) stress in member BD? What is the allowable shear stress in the pin at C? What is the required cross-section area for member BD? What is the minimum thickness t of member BD? What is the required SHEAR cross-section area at point C? What is the minimum diameter for the pin at C? (Solve for a value with the combination of mm and N)
6 kN/m 4 kN/m 1.5 m- What is the concentrated load of the rectangular loading as shown in the figure? 6 KN 2.5 KN 8 KN 4.5 KN
3 An aluminum (shear modulus = 2.8× 1010 Pa) rod is 25 mm in diameter and 50 cm long. One end is rigidly fixed to a support. What torque must be applied to twist the rod 4.5° about its longitudinal axis?
Solve following the problems below and show your complete, systematic and neat solution. Upload your solution with one PDF file. 1. For the beam shown, a. determine the maximum flexural stresses in compression ant tension. b. determine the flexural stress of the fiber located at 3m from the left support and 50 mm above the bottom 18 kN/m 300 mm 6 kN/m 20 mm 27 kNm 22 2m 2m 3 m +m 15 mm - - 50 mm 360 mm 20 mm
A rectangular aluminum block is 100 mm long in the x direction, 75 mm wide in the y direction and 50 mm thick in the z direction. It is subjected to a triaxial loading consisting of a uniformly distributed tensile force of 200 kN in the x direction and uniformly distributed compressive forces of 160 kN in the y direction and 220 kN in the z direction. If V = and E = 70 GPa, determine a single distributed loading in the x(y) direction that would produce the same Z(x) deformation as the original loading. Given: EZ = 1 [oz − v(ox + oy)] - 1 EZ= = 2/6 E ;[−oz − v(ox — oy)]v oz = -29.33MPa (Compression)