2. When working on a high - voltage system , it is best to keep anyone who is not part of the ser vice away from you and the car by creating a buffer zone around the car . Technician A makes sure the outside edges of the zone are at least one foot away from the car . Technician B places B orange cones to define the outer boundaries of the zone. Who is correct ?

2. When working on a high - voltage system , it is best to keep anyone who is not part of the ser vice away from you and the car by creating a buffer zone around the car . Technician A makes sure the outside edges of the zone are at least one foot away from the car . Technician B places B orange cones to define the outer boundaries of the zone. Who is correct ?

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter1: General Information For Electrical Installations

Section: Chapter Questions

Problem 20R: Are low-voltage systems totally safe? Explain.

See similar textbooks

Similar questions

Please answer all questions , and give me a sample answers 1- What is done to prevent a plan from becoming confusing because of too much detail? 2. Does compliance with the NEC always result in an electrical installation that is adequate, safe, and efficient? Why? 3. Name two nationally recognized testing laboratories. 4- Are low-voltage systems totally safe? Explain 5- Explain briefly what an arc flash is 6- Where might you obtain information about on-the-job safety and safety training?
Question 4. Explain why grounding is important for the electrical safety of medical devices and how electrical safety could be improved further.
Please help with the following questions, thank you. Calculate the following : 1) At what voltage is the switching point? 2) The hysteresis spread ?
Technician A says when testing the voltage output, if the charging voltage is too high, the cause could be an open field wire from the regulator. Technician B says a loose or glazed drive belt could be the cause of too high charging voltage. Who is correct? A only B only Both A and B Neither A or B Technician A says that poor connection at the generator output wire can cause charging systems problems. Technician B says that many charging system circuits contain a circuit protection device. Who is correct? A only B only Both A and B Neither A or B
Can you please illustrate in diagram and explain on how to do the Conductance Test of the Motor Control Center Bus Bar. How much the acceptable torence value of the results.
Which of these places has the highest voltage in a properly working truck electrical system with the engine running and the batteries charging? A. Across battery terminals B. Across cranking motor B+ and cranking motor ground C. Across the alternator plus output stud and alternator ground stud cranking motor ground D. All of the above would be the exact same voltage
6. when seeking to measure the voltage of an industrial power supply (600 Volts AC) an electrician needs to do the following to prepare the Simpson 260 meter for measurement (insert the words to make the following statements correct). a. Set the function switch to b. The black lead should be inserted in the jack. C. The red lead should be inserted in the jack. d. The range switch should be set to the position. Did you note the safety warnings in this section? Fairly significant, eh?! Nothing to mess around with!! 7. Why must you "zero" the meter (adjust it for zero (0)) when measuring resistance? 8. Describe the steps needed to accomplish the task of zeroing the meter. (4pts) For the following questions, refer to section 4.19 in the Simpson meter manual. 9. The Rx 1 resistance range is intended for resistances between and Ω. 10. The R x 100 range is intended for resistances between and Ω. 11. The Rx 10,000 range is intended for resistances over 0450…
True or False 1. The point of connection of a motor for its electrical supply is called junction box. 2. The bearing placed in the shaft of the generator is included as stator part. 3. Basically, not all generators are AC generator at first, even DC generator 4. DC generator can be used as an emergency generator. 5. Circuit breakers are used in a motor circuit protection rather than fuses (safety switch).
Lockout is required: During servicing and maintenance where unexpected ener- gization or start-up of equipment could harm employees. During repair and replacement work, and during renovation work. a. b. C. During modifications or other adjustments to powered equipment. d. All of the above. Lockout may involve: Opening a disconnect switch. b. a. Closing a valve. Placing a block in the equipment. d. All of the above. C. Lockout is the process ci Shutting off a machine at the end of a shift. Warning equipment operators about the risks involved in bypassing a machine guard. Preventing the flow of energy from a power source to a piece of equipment, and keeping it from operating. a. b. C. d. Preventing mechanics from starting repairs without the machine operators' knowledge. Tagout: Serves as a warning. b. Physically restrains a person from operating a power source. Must be applied using specialized tagout tools. a. C. d. Must be worn like a badge by the employee who is doing the repairs.…
Question 10A-How is the minimum number of receptacle outlets determined for theliving room? What article of NEC is talking about this? B-What must be installed wherever outlets are required according to theNEC? What article of NEC is talking about this requirement?C-Which part of the NEC standard proposes the switches requirements? D-If the branch circuits supplying the receptacles in the figure at 15 A,what's the minimum size of the conductors in the branch circuit? E-According to the AEC standard, how many outlets can a GFCI protect?
Who has the responsibility for Code interpretations? When are rules in the PEC mandatory and when are they advisory? What color-coding is required on multiwire branch circuits? What is the basis for figuring the general lighting loads in occupancies?
QUESTION-3: In the system with open and closed protection zones given in the figure below: a) Which breakers will open for fault at point F1? 5) For a fault at point F2, if B3 fails to operate, which breakers should be operated to provide Dack-up protection? B3 F2 BS F1 B1 B2 84