Technician A says when testing the voltage output, if the charging voltage is too high, the cause could be an open field wire from the regulator. Technician B says a loose or glazed drive belt could be the cause of too high charging voltage. Who is correct? A only B only Both A and B Neither A or B Technician A says that poor connection at the generator output wire can cause charging systems problems. Technician B says that many charging system circuits contain a circuit protection device. Who is correct? A only B only Both A and B Neither A or B

Technician A says when testing the voltage output, if the charging voltage is too high, the cause could be an open field wire from the regulator. Technician B says a loose or glazed drive belt could be the cause of too high charging voltage. Who is correct? A only B only Both A and B Neither A or B Technician A says that poor connection at the generator output wire can cause charging systems problems. Technician B says that many charging system circuits contain a circuit protection device. Who is correct? A only B only Both A and B Neither A or B

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter16: Installation Of Heating, Cooling, And Refrigeration Systems

Section: Chapter Questions

Problem 13RQ

See similar textbooks

Similar questions

Which of the following statements is correct? When a fault occurs, Select one: O A. the generator terminal voltage does not change immediately O B. the field current will not change immediately O C. A small regulation error AV forces the AVR to increase the generator field O D. All of the above
a. Draw the relationship between excitation current and short circuit, and Please explain. b. At what volts is the alternator end voltage short-circuited? At nominal voltage What will happen if a short circuit is made?
A step up chopper has an input of 200 volts and output of 250 volts. The blocking period is each cycle is 0.6x10-3 seconds. Find the period of conduction in each cycle and frequency of operation?
3.) The time delay fuse using the strict standard rating for 2Ø, 230 V, 7.5 hp SCIM motor is A. 25 A B. 30 A C. 35 A D. Any of the above
Calculate the reactance voltage for a machine which runs at 900rpm number of commutator segments is 65, brush width is 1.74 (in commutator segments), coefficient of self induction is 153 the conductor current is 27A.
2. Which of the symbols in Figure A6 represents a circuit breaker with thermal overload protection?A. CB. DC. AD. B
25.a. There are two wires labeled P1 and P2 at a DC motor's junction box. These wires will attach to whatinternal component of the motor?A. A speed potentiometerB. The parallel windingC. GroundD. A thermostat25.b. As you walk up to a machine, you see a technician tapping on the back section of a DC motor with alead mallet. This technician isA. cleaning the commutator.B. checking for end bell cracks.C. looking for weak or worn brushes.D. reseating the rear end bell on the case.
3 Phase Induction motor I want a short answer please 11. The number of three-phase induction motor parts and the function of each part. 12. How to know the terminals of an induction motor if they are not encoded in the terminal box. 13. How can a three-phase induction motor be reversed? 14. Number of tools used to protect devices - transformers and induction motors - in the laboratory. 15. The number of devices required to conduct a test No load. for a three-phase induction motor 16. The number of devices required to conduct a test For a three-phase induction motor, a Blocked rotor 17. What is the use of a test? For a three-phase induction motor? Blocked rotor and No load 18. When conducting the no-load test, the current rises in the first second of preparation when using the direct connection method. the reasons for that? 19. When performing a non-pregnancy test, we notice a decrease in the ability factor. the reasons for that? 20. Connect an induction motor directly to the source.…
Magnetic Tape Recording Explain briefly the mechanism of Magnetic Tape Recording and how is induced electromagnetism applied in such. Magnetic Levitation (MagLev) Traing Explain briefly the mechanism of Magnetic Levitation (MagLev) Train and how is induced electromagnetism applied in such. Ground Fault Interrupter Explain briefly the mechanism of Ground Fault Interrupter and how is Faraday’s Law applied in such. Induction Stove Explain briefly the mechanism of Induction Stove and how is Faraday’s Law applied in such. Explain short and concise. Thank you.
Explain how the following adjustments are made in a single phase induction type energy meter: (a) Lag adjustment (b) Adjustment for friction compensation (c) Creep (d) Overload compensation (e) Temperature compensation
5.a. A characteristic common to most steam-turbine alternators isA. belt drive.B. salient-pole rotor construction.C. gear drive.D. cylindrical rotor construction.5.b. The stator core of an alternator is safeguarded against high short-circuit current by a device called aA. surge capacitor.B. lightning arrester.C. differential protector.D. temperature detector.
Choose the right answer. 1. The basic elements in any power system are 2. The reactors have the following problems 3. If a fault occurred between phases (A, B, and C) simultaneously the fault is called if the fault occurred on phase (A) only or phases (A, B), it may take the following types and ...... where or 4. The symmetrical component method is 5. Conditions for succesful operation of a power system are 6. The reason we use the numerical methods in load flow analysis is 7. The main diagonal of Y-bus numbers by a factor / not any) 8. The properties of the fault currents and (changes the signs / keeps the signs / multiplies the .... .... ....... re