1. Find T(x,t) for a case of transient one dimensional heat transfer with T=0 at both ends for all time and an initial temperature distribution given by f(x) = -4x²+8x³-5x²+x. Assume a dimensionless length scale with ends at 0 and 1 and α = 2 1/sec. Plot the initial temperature distribution and the temperature distribution at 5 seconds.

1. Find T(x,t) for a case of transient one dimensional heat transfer with T=0 at both ends for all time and an initial temperature distribution given by f(x) = -4x²+8x³-5x²+x. Assume a dimensionless length scale with ends at 0 and 1 and α = 2 1/sec. Plot the initial temperature distribution and the temperature distribution at 5 seconds.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.32P

See similar textbooks

Similar questions

Q.5/ Find the temperature distribution for the following heat problem in dimensionless variables; Uxx - 2ut = 0 0 0 ux (0, t) = 0, u(1, t) = 0 and u(x,0) = x when 0 < x <1
1. Consider heat transfer from a circular cylinder whose axis is normal to a forced flow and which is rotating at an angular velocity, w. If the surface of the cylinder is maintained at a uniform temperature, find the dimensionless parameters on which the Nusselt number depends on.
Consider a wall of thickness 50 mm and thermal conductivity 14 W/m.K, the left side (x-0) is insulated. Heat generation (q,) is present within the wall and the one dimensional steady-state temperature distribution is given by T(x) = ax +bx+c [°CJ, where c 200 °C, a = -1144 °C/m is the heat fluxes at the right side, x L, (kW/m)? b= needs to he determined, and x is in meters. What 9, K 4L) Insulation
In the Fig. 2 below, let Ki = K2 = K and ti = t=t. %3D T -T X Fig. 2 (a) Let T= 0 °C and T= 200 °C. Solve for T: and unknown rates of heat flow in term of k and t. MEC_AMO_TEM_035_02 Page 2 of 11 Finite Element Analysis (MECH 0016.1) – Spring - 2021 -Assignment 2-QP (b) Let T- 400 °C and let fs have the prescribed value f. What are the unknowns? Solve for them in term of K, t, and f.
3. Find the two-dimensional temperature distribution T(r,z) under steady state condition. Where, To=20 °C, TL=5200 °C. The density, conductivity and specific heat of the material are p 800 kg/m³, k=200 W/m.K, and cp=2500 J/kg.K, respectively. Also, r= 520 cm and L=1040cm. To TL L To
You have a 1-D steady-state conduction problem, constant thermal properties, with energy generation q_dot. The material is 4.0 cm thick and has a constant thermal conductivity of k = 65.0 (W/m-k). The temperature distribution within the object is: T(x) = a + bx^2 a = 100 Celcius b = -1000 Celcius/m^2 Starting with the Heat Diffusion Equation and using the data given above, determine the following: • Determine the heat generation rate q_dot within the wall. • Determine the heat flux q" at x=0 and at x=L.
The Gilles & Retzbach model of a distillation column, the system model includes the dynamics of a boiler, is driven by the inputs of steam flow and the flow rate of the vapour side stream, and the measurements are the temperature changes at two different locations along the column. The state space model is given by: x = 0 00 -30.3 0.00012 -6.02 0 0 0 -3.77 00 0 -2.80 0 0 Is the system?: a. unstable b. C. not unstable x+ 6.15 0 0 0 0 3.04 0 0.052 not asymptotically stable d. asymptotically stable -1 u y = 0 0 0 0 -7.3 0 0 -25.0 X
Consider a wall of thickness 50 mm and thermal conductivity 14 W/m.K, the left side (x-0) is insulated. Heat generation (q) is present within the wall and the one dimensional steady-state temperature distribution is given by T(x) = ax +bxtc [°C] , where c 200 °C, a = -1285 °C/m , b=needs to he determined, andx is in meters. What is the heat fluxes at the right side, x = L, (kW/m )? 9, K 4L) Insulation
Find the two-dimensional temperature distribution T(x,y) and midplane temperature T(B/2,W/2) under steady state condition. The density, conductivity and specific heat of the material are p= 62400 kg/m', k-400 W/m.K, and cp=2500 J/kg.K, respectively. A uniform heat flux q%=1000 W/m² is applied to 2. the upper surface. The right and left surfaces are also kept at 0°C. Bottom surface is insulated. 9% (W/m³) y4 T = 0 °C T = 0°C W= 520 cm B=1560 cm
Find the two-dimensional temperature distribution T(r,z) under steady state condition. Where, To=20 oC, TL=8200 oC. The density, conductivity and specific heat of the material are ρ =800 kg/m3, k=200 W/m.K, and cp=2500 J/kg.K, respectively. Also, r1=820 cm and L=1640 cm.
For the model defined in Question 1, is the closed loop system with the negative feedback control law? 0 0 0 ;]* X 0 u=-Kx= O a. O b. O c. unstable 0 1 0 asymptotically stable not unstable O d. not asymptotically stable
1. A spring mass system serving as a shock absorber under a car's suspension, supports the M 1000 kg mass of the car. For this shock absorber, k = 1 × 10°N /m and c = 2 × 10° N s/m. The car drives over a corrugated road with force %3| F = 2× 10° sin(@t) N . Use your notes to model the second order differential equation suited to this application. Simplify the equation with the coefficient of x'" as one. Solve x (the general solution) in terms of w using the complimentary and particular solution method. In determining the coefficients of your particular solution, it will be required that you assume w – 1z w or 1 – o z -w. Do not use Matlab as its solution will not be identifiable in the solution entry. Do not determine the value of w. You must indicate in your solution: 1. The simplified differential equation in terms of the displacement x you will be solving 2. The m equation and complimentary solution xe 3. The choice for the particular solution and the actual particular solution x,…