Convection H.T. Q3: In an industrial facility, air is to be preheated before entering a furnace by geothermal water at 120°C flowing through the tubes of a tube bank located in a duct. Air enters the duct at 20°C and 1 atm with a mean velocity of 4.5 m/s, and flows over the tubes in normal direction. The outer diameter of the tubes is 1.5 cm, and the tubes are arranged in-line with longitudinal and transverse pitches of SL = Sr = 5 cm. There are 6 rows in the flow direction with 10 tubes in each row. Determine the rate of heat transfer per unit length of the tubes, and the pressure drop across the tube bank. For this square in-line tube bank, if the friction coefficient is 0.16. Also, the correction factor 1 for the square arrangements. Properties: (p = 1.06 kg/m', k =0.02808 W/m °C, u = 2.008x10-5 kg/m.s, Pr = 0.7202 and Cp= 1007 J/kg.K). Take C, = 0.286, C2 = 0.95 and m = 0.608. Ans. q = 23.12 kW, AP = 21 Pa]

Convection H.T. Q3: In an industrial facility, air is to be preheated before entering a furnace by geothermal water at 120°C flowing through the tubes of a tube bank located in a duct. Air enters the duct at 20°C and 1 atm with a mean velocity of 4.5 m/s, and flows over the tubes in normal direction. The outer diameter of the tubes is 1.5 cm, and the tubes are arranged in-line with longitudinal and transverse pitches of SL = Sr = 5 cm. There are 6 rows in the flow direction with 10 tubes in each row. Determine the rate of heat transfer per unit length of the tubes, and the pressure drop across the tube bank. For this square in-line tube bank, if the friction coefficient is 0.16. Also, the correction factor 1 for the square arrangements. Properties: (p = 1.06 kg/m', k =0.02808 W/m °C, u = 2.008x10-5 kg/m.s, Pr = 0.7202 and Cp= 1007 J/kg.K). Take C, = 0.286, C2 = 0.95 and m = 0.608. Ans. q = 23.12 kW, AP = 21 Pa]

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.53P

See similar textbooks

Similar questions

7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
Q2) Air at 20°C flows over a flat plate having a uniform heat flux of 800 W/m². The flow velocity is 4m/s and the length of the plate is 1.2 m. Determine the value of heat transfer coefficient and also the temperature of the plate as the air leaves the plate.
Water enters a tube at 29°C with a flow rate of 460 kg/h. The rate of heat transfer from the tube wall to the fluid is given as qs′(W/m)=ax, where the coefficient a is 25 W/m2 and x(m) is the axial distance from the tube entrance. (a) Beginning with a properly defined differential control volume in the tube, derive an expression for the temperature distribution Tm(x) of the water. (b) What is the outlet temperature of the water for a heated section 31 m long? (c) Sketch the mean fluid temperature, Tm(x), and the tube wall temperature, Ts(x), as a function of distance along the tube for fully developed and developing flow conditions. (d) What value of a uniform wall heat flux, qs″ (instead of qs′=ax), would provide the same fluid outlet temperature as that determined in part 8.13b? For this type of heating, sketch the temperature distributions requested in part 8.13c.
Air is flowing through a 20 m long pipe of 20 cm diameter at a rate of 0.8 kg/s. The inlet air temperature is 40 deg C; the entire pipe wall is held at a constant temperature of 90 deg C. Estimate the air temperature at the outlet as well as the heat transfer rate for the entire length of the pipe. Properties are: 1.038 kg/m3; 1009 J/(kg-K); 2.042E-05 Pa-s; 0.0293 W/(m-K).
43% uo 7:52 * ZAIN IQ I. sheet No.3.pdf Homework 01-03 -2021 one-dimensional heat transfer and disregarding radiation, determine the rate of heat transfer through the wall. Q4/ Steam at Te1-320°C flows in a cast iron pipe (k=80W/m.°C) whose inner and outer diameters are D =5cm, and D=5.5cm, respectively. The pipe is covered with 3 cm thick glass wool insulation with k=0.05W/m.°C. Heat is lost to the surroundings at T02=5°C_by natural convection and radiation, with a combined heat transfer coefficient to be h,=18W/m.C. Taking the heat transfer coefficient inside the pipe to be h,=60W/m.C, determine the rate of heat loss from the steam per unit length of the pipe. Also determine the temperature drops across the pipe shell and the insulation. 05/ Determine the overall heat transfer coefficient U based on the outer surface of a D=2.5cm, and D=3.34 cm steel pipe (k=54.0W/m.°C) for the following conditions: inside and outside heat transfer coefficients are 1200W/m."C. and 2000W/m."C…
Q3. White potatoes (k = 0.50 W/m. °C and a = 0.13 x 106 m²/s) that are initially at a uniform temperature of 25°C and have an average diameter of 6 cm are to be cooled by refrigerated air at 2°C flowing at a velocity of 4 m/s. The average heat transfer coefficient between the potatoes and the air is experimentally determined to be 19 W/m². °C. Determine how long it will take for the center temperature of the potatoes to drop to 6°C.
Q1) In a process water at 30°C flows over a plate maintained at 10°C with a free stream velocity of 0.3 m/s. Determine the hydrodynamic boundary layer thickness, thermal boundary layer thickness, local and average values of friction coefficient, heat transfer coefficient and refrigeration necessary to maintain the plate temperature. Also find the values of displacement and momentum thicknesses. Consider a plate of 1 mx 1 m size.
Question 2 Air (Cp= 1.005 kJ/kg.°C) enters a 7-m-long, 7.2-cm-diameter pipe at 63°C at a rate of 0.06 kg/s. The air cooled at an average rate of 320 W/m² surface area of the pipe. The air temperature at exit of the pipe is:
In many manufacturing plants, individuals areoften working around high-temperature surfaces.Exposed hot surfaces that can cause thermal burns on humanskin are considered hazards in the workplace. Metallic surfacesabove 70° C can instantly damage skin that touches them.Consider an AISI 1010 carbon steel strip (? = 7832 kg/ m 3 )2 mm thick and 3 cm wide that is conveyed into a chamber tobe cooled at a constant speed of 1 m/s. The steel strip entersthe cooling chamber at 597° C. Determine the rate at whichheat needs to be removed so that the steel strip exits the chamberat 47° C . Discuss how the conveyance speed can affect therequired rate of heat removal.
A liquid enters a 2.5-cm-diameter tube with a length of 5.0 m. The liquid inlet temperature is 20°C and thetube wall temperature is 60°C. Average liquid properties are Cp = 2.0 kJ /kg·K, μ = 10 mPa·s, andr = 900 kg/m3. At a flow rate of 1200 kg/h, the liquid outlet temperature is measured to be 30°C. a) Estimatethe liquid outlet temperature when the flow rate is reduced to 400 kg/h. b) What is the thermal resistancefor convection inside the pipe? (Answer 38.3°C)
Q2/A stainless steel ball (p 8055 kg/m3, Cp- 480 J/kg C) of diameter D 15 cm is removed from the oven at a uniform temperature of 350°C. The ball is then subjected to the flow of air at 1 atm pressure and 30°C with a velocity of 6 m/s. The surface temperature of the ball eventually drops to 250°C. Determine the average convection heat transfer coefficient during this cooling process and estimate how long this process has taken. Ans =23.75 min
300960 W (e) Water is entering a heated tube at mass flow rate of 1.2 kg/s. The temperature at the inlet is 20°C and at the outlet is 80°C. Assume the surface temperature of the tube is 100°C. The convection coefficient of the water flow is 28 W/m².°c. The specific heat and density of water can be assumed to be 4180 J/kg.°C and 990 kg/m³. What is the rate of heat transfer to water during this process?