Decide on the type of problem for each question.
- a. For the meter stick example, tests have been conducted for extensions of 0.2, 0.4, 0.6, and 0.8 meters with loads of 2, 4, 6, and 10 coins and 5 large books in each test. What will the deflection be for 0.5 meters and 8 coins?
- b. If no books are used to hold one end of the beam, what will be the maximum number of coins that can be placed on the tip?
- c. For the meter stick example, we have deflection data for a 0.7 meter extension with 6 coins. What will the deflection be for 3 coins?
- d. For the meter stick example above, will 5 stacked coins placed on the tip yield a greater or smaller deflection than 5 coins placed along the beam only one high?
(a)
Find out the type of problem the given question corresponds.
Answer to Problem 1ICA
The given question corresponds to a parametric problem.
Explanation of Solution
Discussion:
The given question is about a test conducted for a meter stick with the extensions as 0.2 m, 0.4 m, 0.6 m and 0.8 m and with loads as 2,4 6 and 10 coins and 5 large books in each test. In this particular question a range of load and extension values is required.
This can be done in an easier way using spreadsheet along with graph for the range of input values. Therefore this problem can be grouped under the heading parametric.
Conclusion:
Hence, the given question corresponds to a parametric problem.
(b)
Find out the type of problem the given question corresponds.
Answer to Problem 1ICA
The given question can be referred to as a Discussion Problem as well as an Ideal Problem.
Explanation of Solution
Discussion:
In the given question it is required to find out the maximum number of coins that can be placed on the tip. We are required to study about the extension of the bean and it’s mass in comparison to that of coin. This therefore can be referred to as a discussion problem.
Half of the length of the beam should remain on the table or else it would fall off without any coin on the tip. Once the course in statics is completed by the student, the given problem can also be referred to as an ideal problem.
Conclusion:
Hence, the given question can be referred to as a Discussion Problem as well as an Ideal Problem.
(c)
Find out the type of problem the given question corresponds.
Answer to Problem 1ICA
The given question can be referred to as a Ratio.
Explanation of Solution
Discussion:
In the given question we are required to find out the deflection of 3 coins given that the deflection data of 6 coins for a 0.7 m extension is given.
The deflection will be double if the number of coins that is the load is doubled. Similarly if the load will be halved the deflection will be halved. We can infer this even if the governing equation is not known. Therefore in this question we are comparing a quantity with a known quantity therefore it is termed to be a ratio.
Conclusion:
Hence, the given question can be referred to as a Ratio.
(d)
Find out the type of problem the given question corresponds.
Answer to Problem 1ICA
The given question can be referred to as a Discussion.
Explanation of Solution
Discussion:
In the given question we are required to find out whether 5 coins placed on the tip yields greater or smaller deflection than the coins placed along the beam only one high.
If the coins are lined up, we get a distribution load which is more difficult to analyze than a point load this can however be easily understood through discussion as to how the distributed load will produce lesser deflection than the point load at the tip.
Therefore the given question can be inferred to be a discussion.
Conclusion:
Hence, the given question can be referred to as a Discussion.
Want to see more full solutions like this?
Chapter 6 Solutions
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
- How do you solve for the approximate life span of wire ropes?arrow_forwardGood day. I am trying to review for examinations and require assistance for these questions... Horse Power: An amount of work performed is 11,500ft-lb per seconds. How much hp is expended in this case? Piston Displacement: A four-cylinder aircraft engine has a total displacement of 275 cu. in. What is its cylinder bore or diameter if each of the four cylinders has a stroke of six inches? Compression Ratio: If there are 243 cubic inches of space in the cylinder when the piston is at the bottom and there are 27 cubic inches of space when the piston is at the top of the stroke. Find CR and V1 (Litre). **Would appreciate a detailed explanation. Thank you so much.arrow_forwardLESSON: ZEROTH LAW OF THERMODYNAMICS AND TEMPERATURE MEASUREMENTMODIFIED TRUE or FALSE Directions: Write TRUE if the statement is correct, otherwise, change the underlined word/s or values to make the statement correct. Write your answer on the space provided before each item number. Statement: The Philippine one-peso coin has a diameter of 23.0 mm at 25 room temperature. Assume that the coin is made up of steel.14. The increase in coin’s diameter when placed in boiling water is 0.0207 mm.15. The final length of coin when placed in boiling water is 23.207 mm.16. If the coin is heated at 42 degrees Celsius, then the increase in diameter is 0.0207 mm.17. If the initial temperature is doubled, then the increase in coin’s diameter when placed in boiling water is 0.0414 mm.arrow_forward
- A composite spring consists of a steel close-coiled helical spring and a bronze close- coiled helical spring arranged in series. Data for the springs are given in the table below: Steel Spring Bronze Spring D 40 mm 40 mm 4.5 mm 4.5 mm G 80 GPa 40 GPa TAllowable 250 MPa 181 MPa 10 Determine the ratio between the number of coils in each spring if the deflection of the two springs is to be the same. Calculate the number of coils of the bronze spring Calculate the maximum load that can be carried by the composite spring. Determine the total extension of the composite spring when subjected to the maximum load. * Calculate the total strain energy in the spring assembly.arrow_forward1.) A ladder rests against a vertical wall at a point 15 ft. above the floor. The angle formed by the ladder and the floor is 71°. Sketch the system described above and answer the following, expressing your answers with 3 significant digits. a. What is the length of the ladder? b. How far from the wall is the foot of the ladder? c. What is the angle between the wall and the ladder? d. What are (a) and (b) in meters?arrow_forwardF P F- b 30 mm 50 30 mm mm Solution workout of this question with proper FBD has to be submitted in MS Teams. Please note down (screenshot) this question. A cutter is about to cut a cable with its jaws parallel as shown. The dimension b=0.071 m, and the applied force at the handles is F=17.4 N. Choose from the options below (a) the force on the cable, and (b) the force in the member PQ.arrow_forward
- A 11-m uniform beam is hinged to a vertical wall and held horizontally by a 5.0-m cable attached to the wall 4.0 mm above the hinge. The metal of this cable has a test strength of 1.00 kN, which means that it will break if the tension in it exceeds that amount. Part A: What is the heaviest beam that the cable can support with the given configuration? Express your answer in kilonewtons. Part B: Find the horizontal component of the force the hinge exerts on the beam. Express your answer in newtons. Part C: Find the vertical component of the force the hinge exerts on the beam. Express your answer in newtons.arrow_forward13 Two objects are weighed, giving 100 ± 0.5 g and 50 ± 0.3 g. What will be the average error of the sum of the two weights? (10.69) Vestarrow_forward16. There are 4 materials that were exposed to different forces and their corresponding elongation is given. Which will have the greatest and lowest value of k. Material A was exposed to 100 N force and elongation is 0.02 meters. B was exposed to 200 N force and elongation is 0.05 meters. C was exposed to a force of 300 N and elongation is 0.07 meter, D was exposed to 400N force and elongation is 0.09 meter.arrow_forward
- Question 2 You have been contracted by a company to design a system for them. The system requires that you use a very elastic material but the materials available to you are Material A which has a Young's Modulus of 210,000 N/mm² and Material B which has a Young's modulus of 12,500 N/mm2 i. ii. Which material will best suit the job. Hint: Explain using the deflection and stiffness equation.arrow_forwardcalculate the theoretical stress using the flexure or bending stress formula. The experimental se is shown in Figure 1: • L LB 10 inches w = 1.5 inches t = 0.25 inches LB Take a few minutes to solve the following pre-lab exercise problems before continuing with the background unit: Problem 1: An experiment was set up according to Figure 1 with the following: L=12 inches Figure 1: Simple cantilever beam with single longitudinal strain gage Search t P = 4 lbs With the load applied, the longitudinal strain gage reading was recorded as 83 us (microstrain). Determine the elastic modulus of the beam material. What material is it? MEXYarrow_forwardA piece of steel rebar is tested in tension to determine its mechanical properties. The length of the sample is 87.3 mm and the cross-sectional area is 52.1 mm². When stretched by 37.2 mm, the force measured is 14,884 N. At this point, the graph is non-linear, but no clear neck is visible. If the Poisson's ratio of the material is 0.281, calculate the cross-sectional area (mm²) at this point.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY