2. Your automobile has to collect data for its anti-lock braking system, such that data is collectedfast enough from each anti-skid sensor (one on each wheel) to obtain a reading once per 1 cmof travel at a speed of 100 km/h from every wheel. What sampling frequency does your sensordata collection system need to have in order to collect data from all wheels? If the datatransmitted is an 8 bit number, what data rate would your system need to have?Insert a picture of your work.Sampling frequencyHzData rate =bits / second Answer the following questions, to test your understanding of sampling frequency and bit depth.1. You are part of new automobile design team, and are responsible for designing the sensor datacollection system. The specification of the data collection system is that is must be capable ofreceiving data with a resolution down to 0.1% of full scale (1 part in 1000) for any given sensor.For example, suppose the driver pushes the gas pedal, the motion of which is read by anelectronic sensor such that the range of motion is defined from 0 (not pressed) to 1 (fullypressed). If you want 0.1 % accuracy, you need 1000 possible data values between 0 and 1.How many bits do you need to represent data to 0.1% accuracy?Insert a picture of your work.

Answered: Image /qna-images/answer/2b0a3ce3-c649-4906-a3df-1798209b076c.jpg

You are part of new automobile design team, and are responsible for designing the sensor data collection system. The specification of the data collection system is that is must be capable of receiving data with a resolution down to 0.1% of full scale (1 part in 1000) for any given sensor. For example, suppose the driver pushes the gas pedal, the motion of which is read by an electronic sensor such that the range of motion is defined from 0 (not pressed) to 1 (fully pressed). If you want 0.1 % accuracy, you need 1000 possible data values between 0 and 1. How many bits do you need to represent data to 0.1% accuracy?

You are part of new automobile design team, and are responsible for designing the sensor data collection system. The specification of the data collection system is that is must be capable of receiving data with a resolution down to 0.1% of full scale (1 part in 1000) for any given sensor. For example, suppose the driver pushes the gas pedal, the motion of which is read by an electronic sensor such that the range of motion is defined from 0 (not pressed) to 1 (fully pressed). If you want 0.1 % accuracy, you need 1000 possible data values between 0 and 1. How many bits do you need to represent data to 0.1% accuracy?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A. A customer asked you to explain your choice of a temperature sensor that you used for his PCB. Initially, there were two sensor options. To compare between them, you decided to test their accuracy and precision. Accuracy of a sensor is a measure of how near its reading is to the real value, the nearer the measured value to the real value the better. While precision is a measure of how widely spread the readings of a sensor are [relative to each other] when measuring the same variable, the narrower the spread the better. So, you tested the two sensors by measuring the same temperature, which was 100 C of boiling water, and you recorder the following 10 measurements of each sensor. Which Sensor has higher accuracy, and which one has higher precision. Sensor Sensor readings when measuring 100 C 99.65 100.05 103 102 99.3 s1 100.1 99.1 100.5 99 98.8 98.78 96.9 101.4 98.88 99 S2 99.12 98.9 99 98.69 99.2
b) Figure 1 shows the calibration data of a sensor. Determine the static sensitivity at the input of X= 0, X= 5 and X= 10. For which input values is the system more sensitive? Calibration Data 300 250 y = 0.875x1.055 200 150 100 50 20 40 60 80 100 120 Input value, cm Figure 1 c) Suppose you found a dial thermometer in a stockroom. Discuss several methods by which you might estimate random and systematic error in the thermometer? How would you estimate its uncertainty? Output value, V
A temperature sensor Pt100 has a rage from -200C to 850C as shown in the figure. Considering the function is linear, find the sensitivity of the sensor? How can we ?improve the sensitivity of this sensor Resistance vs. Temperature- Pt100 (385) 400 350 300 250 200 150 100 50 -200 100 100 200 300 400 50 600 700 800 900 Temperature ["c) Resistance [Ohms]
b) A linear variable displacement transducer (LVDT) senses displacement and indicates a voltage output, which is linear to the input. Figure 1 shows an LVDT setup used for static calibration. It uses a micrometre to apply the known displacement and a voltmeter for the output. i) Suggest the independent, dependent and extraneous variables in this calibration. ii) Indicate the basic functional elements of the device in Figure 1 in the form of block diagram. 10 Micrometer Fixed mounts Connector Excitation voltage in Figure 1 Primary coil xx_w_ LVDT E Output voltage 10.135 Voltmeter Secondary coil Core
After some engine model replacement, an aircraft model is experiencing some aggressive nose up phenomenon which may lead to stall. To combat this problem, a new control system has been introduced to the Flight Control Computer, FCC. When activated, the new system measure the aircraft pitch from an Angle of Attack, AOA sensor to analyze either the aircraft is nosing up or down. If the pitch angle is too high, describing that the aircraft might be in a dangerously nose up position, the FCC will gain control of the horizontal stabilizer using a linear motor (FIG 1), thus bringing the nose of the aircraft down into safer pitch angle range (FIG 2). a. What is the input/output of the control system? b. Is this system is a close loop or open loop? c. What is the actuator used in this control system? d. Draw the Block Diagram to describe the control system. Horizontal stabilizer Pivot Horizontal stabilizer 000000c Jackscrew moves the angle of the horizontal stabilizer up or down. Motor Figure…
The Vehicle stands at point [2,1]' and theta angle 45degree on World frame. The sensor mounted at [1,0] point on Vehicle. The sensor has detected an obstacle at point [2,-1] on Sensor frame. Firstly calculate from the sensor frame to the Word frame Homegenous transformation Matrix step by step. Find the obstacle position on World frame? y4 W
4:07 3G l. Moodle A bbb2.du.edu.om EE ...Session (15-3- Said Grami O College of Engineering Vision for the Future Question 3 During a step function calibration, a first-order instrument is exposed to a step change of 200 units. 1- If after 1.5 s the instrument indicates 140 units, find the instrument time constant. 2- find the error in the indicated value after 2 s S. 3- Find the raise time at 90 % of the system. y(0)=0 units; K=1 unit/unit. Question 4 A first order instrument with a time constant of 2 seconds is to be used to measure a periodic input. If a dynamic error of ±2% can be tolerated, 1- determine the maximum frequency of periodic input that can be measured. 2- What is the associated time lag (in seconds) at that frequency? MECH374: Instrumentation and Measurement Said Grami Practice
1- Change in temperature is a physical input variable of a sensor. Select one: True False
PIoVide ue comect u We want to design an experiment to measure oscillations of a simple pendulum on the surface of Jupiter with acceleration due to gravity g= 30 ms 2. We have to make do with a rudimentary video camera with a frame rate of 15 Hz to record oscillations in a pendulum and use it to measure the frequency of oscillation. The smallest length of the pendulum that we can send so that the correct oscillation frequency can be measured is cm. Assume perfect spatial resolution of the camera and ignore other "minor" logistical difficulties with this experiment.
PartII Say you've deployed a robot that can can measure electric field due to specified charge at the specified location with good accuracy. And you got these results from the robot: Electric field due to q2 at point p1 is (-1667.0) i + (18340.0) j Electric field due to q3 at point p1 is (-2496.0) i + (–1628.0) j Electric field due to q1 at point p2 is (-6311.0) î + (2470.0) } Electric field due to q2 at point p2 is (-11585.0) î + (–6951.0) ĵ Electric field due to q3 at point p2 is (4657.0) î + (11310.0) } c) Find the net Electric field at pj .
A nearsighted eye is corrected by placing a diverging lens in front of the eye. The lens will create a virtual image of a distant object at the far point (the farthest an object can be from the eye and still be in focus) of the myopic viewer where it will be clearly seen. In the traditional treatment of myopia, an object at infinity is focused to the far point of the eye. If an individual has a far point of 39.5 cm, prescribe the correct power of the lens that is needed. Assume that the distance from the eye to the lens is negligible.
You are watching a live concert. You can also find the concert streaming live on Spotify. About how far must you stand from the stage in order for the live concert and the live stream to be perfectly in sync? HINT: Assume the radio signal (Spotify) has to travel all the way around the Earth. circumference of the Earth (average): 40,041,000 m Speed of sound: 345 m/s Speed of light: 300,000,000 m/s