Which of the following statements about the SF experiment is/are CORRECT? The monochromator is located following the light source. If sulfuric acid is not available as a solvent, distilled water can be used instead. If Kl is not available as a quencher, KCl can also be used as a substitute. High intensity sources are used in SF instruments.

Which of the following statements about the SF experiment is/are CORRECT? The monochromator is located following the light source. If sulfuric acid is not available as a solvent, distilled water can be used instead. If Kl is not available as a quencher, KCl can also be used as a substitute. High intensity sources are used in SF instruments.

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter32: Gas Chromatography

Section: Chapter Questions

Problem 32.10QAP

See similar textbooks

Similar questions

0.1120 g of a solid sample containing copper was dissolved by acid and transferred to a 250.00 mL volumetric flask and volume was made up with distilled water. The solution was then diluted by a factor of 25. The final solution was analyzed by atomic absorption spectrophotometry and the concentration was found be 2.982 ppm, What is the weight percentage of copper in the original solid sample? Keep four significant figures in your final answer.
Suggest two possible applications for paper chromatography other than the separation of dyes or the identification of metal ions.
2. Calculate the minimum concentration (µg/ml) of bismuth(III) (M=208.98 g/mol) in the analyte, which can still be determined by photometric method using the reaction with thiocarbamide, if the photometric measurements of the solution is carried out in a cuvette with a thickness of the absorbing layer = 1.00 cm, and the minimum value of the Absorbance measured by the spectrophotometer is 0.01. Molar attenuation coefficient = 9,1-10³ mol¹ L cm
Maria was tasked to determine the concentration of a Fe2(SO4)3 solution. She prepared 5 different standards of Fe2(SO4)3 using the table below as her guide. She ran the standards and the unknown solution through UV-VIS spectroscopy and recorded the absorbances of each solution. HINT: use the dilution equation to determine the concentration of Fe2(SO4)3 in each test tube before preparing the standard curve. NOTE: No need to force the line to pass through zero. Just graph the data as is. What is the slope of the line of the standard curve from the given data? What is the concentration of the unknown solution?
You are provided with standard stock solutions containing 1000ppm each of Cu, Mn, K, Na and Ca. You are to perform a standard addition (or spike) on your pill samples to test for matrix interference. Show the calculations for the addition of 5 ppm of each element (Cu, Mn, K, Na, Ca) to your sample pill using the standards you have previously made or been provided with. Assume you will have less than 100 mL of pill solution to work with when making your spiked pill solution. Hint:) Make “spiked” working pill solutions (and sample blank!) by taking 1mL of your original pill solution and quantitatively transferring it solution to a 100 mL volumetric. Add the appropriate amount of your standards to add 5ppm of each element (except being analyzed to your solutions. Fill to the mark with 2% nitric acid (provided). Remember to do the same for your sample blank!
Many ions form colored solutions when dissolved in water. For example, aqueous Cu2+ solutions are light blue and aqueous Ni2+ solutions look light green. These metals in particularare often found in stainless steel. Would you expect their presence in your samples to interfere in the spectrophotometric analysis of permanganate at 525 nm? Why or why not? I think the answer is that I would expect the Cu2+ in my samples to interfere but not Ni2+ because the Ni2+ is green, signifying a higher wave length that the spectrometer wouldn't be able to pick up on because it was only set to 525 (blue-ish) where as the green is 530-ish. I just want to make sure thanks!
one: Topic Molecular Spectroscopy (16 marks) You were given an unknown mixture that contains two metal salts (A) Co(NO3)2 and (B) Cr(NO3)2 and requested to determine their concentration. The following representative information about the absorbance data were also provided. Measurements were made in a 1.0 cm quartz cells. Pure A (mol/l) Pure B (mol/l) 0 Abs @510 nm Abs @575 nm 1.5 x 101 0 6 x 102 Unknown conc in mixture 0.714 0.097 0.298 0.757 Unknown conc in mixture 0.671 0.330 How would you go about calculating the concentration of the two salts?
If Johnny Joestar measured the amount of light absorbed by the analyte in a sample to determine its concentration, what kind of method did he use? Volumetric method Gravimetric method Electroanalytical method Spectroscopic method
2. A chromatographic column is eluted with a solution containing a mixture of two components, X and Y. The chemical affinity of X for the stationary phase is less than that of Y and the chemical affinity for X for the mobile is greater than that of Y. Which substance will be eluted first? Explain your answer.
The data in the table are used to create a calibration curve for the determination of RNA from its absorbance at 260 nm. Use a spreadsheet and the least-squares method to determine the slope and y-intercept of the best straight line fit to the calibration curve. Do not subtract the blank reading when creating the calibration curve. m= RNA (µg) 0.00 10.29 20.58 30.87 41.16 mass= Absorbance at 260 nm 0.227 0.452 0.786 1.078 1.296 Hg-1 Using the slope and intercept of the calibration curve, determine the quantity of RNA in a sample that gives an absorbance of 0.523. µg
The data in the table are used to create a calibration curve for the determination of RNA from its absorbance at 260 nm. Use a spreadsheet and the least-squares method to determine the slope and y-intercept of the best straight line fit to the calibration curve. Do not subtract the blank reading when creating the calibration curve. m = b = RNA (µg) 0.00 10.67 21.34 32.01 42.68 mass= Absorbance at 260 nm 0.224 0.512 0.769 1.145 1.465 Using the slope and intercept of the calibration curve, determine the quantity of RNA in a sample that gives an absorbance of 0.636. µg µg