When a fluid flows over a surface, the shear stresS I (N/m) at the surface is given by the expression du T = - 'dy surface where u is the viscosity (N-s/m), u is the velocity parallel to the surface (m/s), and y is the distance normal to the surface (cm). Measurements of the velocity of an air stream flowing above a surface are made with an LDV (laser-Doppler-Velocimeter). The values given below were obtained. y y 0.0 0.00 2.0 88.89 1.0 55.56 3.0 100.00 At the local temperature, u = 0.00024 N-s/m. In four decimal places, calculate du/dy at the surface using all the points.

When a fluid flows over a surface, the shear stresS I (N/m) at the surface is given by the expression du T = - 'dy surface where u is the viscosity (N-s/m), u is the velocity parallel to the surface (m/s), and y is the distance normal to the surface (cm). Measurements of the velocity of an air stream flowing above a surface are made with an LDV (laser-Doppler-Velocimeter). The values given below were obtained. y y 0.0 0.00 2.0 88.89 1.0 55.56 3.0 100.00 At the local temperature, u = 0.00024 N-s/m. In four decimal places, calculate du/dy at the surface using all the points.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The laminar flow of a fluid with a constant viscosity, 4, inside a channel is governed by the following boundary value problem (strong form): d'u dp for y E (0, h) "dy dr u = 0 at y = 0 and y = h vhere u is the fluid velocity and is the pressure drop in the direction of the flow. a) Derive the weak form of the boundary value problem described above.
A small capillary with an inside diameter of 2.22 x 10-3m and a length 0.317m is being used to continuously measure the flow rate of a liquid having a density of 875 kg/m3 and viscosity of 1.13 x 103 Pa-s. The pressure drop reading across the capillary during flow is 0.0655m water (Density is 996 kg/m3). What is the flowrate in cu.fps?
n = Xe()r -------Equation 1 where X = 1.7419 and (E/R) = -0.018 are constants for a given fluid. You are required to carry out appropriate calculations on the effect of changes in temperature given in table A by using equation 1 for Ethanol on the viscosity of a fluid. Table A NO Temperature viscocity n T°C cP 10 3 20 30 5 40 6. 50 7 60 8 70 In addition to this, calculate other constraints such as the variety of shear stress (T) and force due to fluid viscosity, when the two layers of different compressible Newtonian fluids are contained between two flat plates separated by a distance of 0.05m and fluid moving with the velocity of 2m/s in the horizontal direction. Assume the shear area between the fluid layers is 0.5m². To do this you required to explain, with examples, the effects of temperature and shear forces on Newtonian and non-Newtonian fluid. Also, explain the operation and constraints of different viscometers that quantify viscosity in fluids. 2.
A dimensionless expression that is significant quantities in the area of viscous flow through channels is called Reynolds number, Re, defined as pDV/u where is p the fluid density, V the mean fluid velocity, D the pipe diameter, and u the fluid viscosity. A Newtonian fluid having a viscosity of 0.38 N-s/m2 and a specific gravity of 0.91 flows through a 25-mm-diameter pipe with a velocity of 2.6 m/s. Determine the value of the Reynolds number in SI Units.
Figure 0 shows the change in density of a newtonian fluid with temperature, ing/m^3.Falling spere experiments give average times of 0.2s @ 10 c and 0.23s @ 20 cUsing the equation u=K(ps-pf)tWhere K is found to be 1.34Ps=2300 kg/m3Calculate the viscosity of the fluid at 20 c and 10 c
The kinematic viscosity of and specific gravity of a liquid are 3.5 x 10-4 m^2 /s and 0.79, respectively. What is the dynamic viscosity of the liquid in N-s/m^2?
Oxygen reaches the veinless cornea of the eye by diffusing through its tear layer, which is 0.60-mm thick. How long does it take the average oxygen molecule to do this? The diffusion constant of oxygen through water is 1.0 x 10-⁹ m²/s. Hint 1. Treat this as a one-dimensional problem. 2. Convert to minutes. 3. Think about the length of the time interval you have calculated. Enter to 2 significant figures Average time taken by O₂ molecule through the tear layer = 30 minutes As a comparison, calculate the time it takes for oxygen to diffuse through a cell membrane about 10 nm thick. Note: Enter time in seconds instead of minutes. Enter to 2 significant figures Average time taken by O₂ molecule through the cell membrane = 0.5 S
. Ooredoo = Question 1 Not yet answered Marked out of 3.00 Flag question 9:01 PM moodle.nct.edu.om Private Determine the kinematic viscosity (Stokes) of oil having the relative density as 0.86. The shear stress at a point in oil is 1.56 N/m² and the velocity gradient at that point is 0.36 per second. Solution: (i) Viscosity (in Ns/m²) = (ii) Dynamic Viscosity (in poise) = (iii) Mass density of oil (in kg/m³) = 65% iv) Kinematic viscosity (in stokes) = ▼
The pulmonary artery, which pumps blood from the heart to the lungs, has an inner radius of 18.8 mm and is 4.82 cm long. If the pressure drop between the heart and lungs is 1,275 Pa, what is the volume flow rate of blood in the pulmonary artery? Give your answer in cm3/s with two digits of precision. The viscosity of blood at 37°C is 2.1 x 103 Pa s. Your Answer: Answer
COE0051 FLUID MECHANICS 2 PROPERTIES OF FLUIDS Section Break (Continuous)- 1. A 30x60 cm plate is pulled through the oil with viscosity of 0.05 kg/m-s. The distance between the parallel plates are 1.5 cm. If the plate is need to pull at the rate of 0.4 m/s, what is the force needed to attain this velocity? FIXED PLATE лиши 1.5 cm FIXED PLATE October 20, 2022 .5 cm 1.0 cm .4 m/s
The viscosity of motor oil is 4.79× 10-³ N. s/m², motor oil is used as a lubricant between two machine parts. The variation in velocity of the oil is 1.6 m/s and a maximum shear stress is 62.8 N/m². What is the required spacing between machine parts in millimeter?
Determine the dynamic viscosity (Pa-sec) and kinematic viscosi ty (m2/s) of vater with a specific weight of 9.81 kN/m3, if a Falling Sphere Viscosimeter test is conducted using an alumi num sphere that has a diameter of 10 mm and a specific weight of 28.06 kN/m3. The theoretical terminal velocity of the sphere is 0.650 m/s www.