When a capillary tube of radius 0.45 mm is dipped into water, the levei inside the capillary tube rises to height 3cm above the surface of the water. calculate the surface tension of water, if its angle of contact is zero and its densityis 1 g/cm³, g = 9.8 m/s².ی طرف نقاط

Name: When a capillary tube of radius 0.45 mm is dipped into water, the lev
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: When a capillary tube of radius 0.45 mm is dipped into water, the levei inside the capillary tube rises to height 3cm above the surface of the water. calculate the surface tension of water, if its angle of contact is zero and its densityis 1 g/cm³,

Answered: Image /qna-images/answer/649207de-d53e-4d4b-9d71-cb47bc97714b.jpg

Engineering

Mechanical Engineering

When a capillary tube of radlus 0.45 mm is dipped into water, the levei inside the capillary tube rises to helgint 3 cm above the surface of the water. calculate the surface tension of water, if its angle of contact is zero and its density Is 1 g/cm3, g = 9.8 m/s2, ش طرق نقاط

When a capillary tube of radlus 0.45 mm is dipped into water, the levei inside the capillary tube rises to helgint 3 cm above the surface of the water. calculate the surface tension of water, if its angle of contact is zero and its density Is 1 g/cm3, g = 9.8 m/s2, ش طرق نقاط

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Similar questions

A factory's pressure tank rests on the upper base of a vertical pipe whose inside diameter is 1 ft. and whose length is 40 ft. The tank is a vertical cylinder surmounted by a cone, and it has a hemispherical base. If the alti-tudes of the cylinder and the cone are respectively 6 ft. and 3 ft. and if all three parts of the tank have an inside diameter of 6 ft., find the volume of water in the tank and pipe when full.
A fluid filled container is shown below. Oil fills the left side of the “U” to a depth of 33.0 cm while water fills the rest. The oil has a density of 753 kg/m3. The radius of the tube on the left side is 27.0 cm and the radius of the tube on the right side is 38.0 cm. a. If the height of the fluid in the two cylinders is exactly the same, what mass should be placed on the left cylinder to balance the system. b. What is the pressure at the bottom of the oil when the system is balanced? c. If the mass on the left is removed, what is the difference in heights between the two sides?
The volume and average density of an irregularly shaped object are to be measured using a spring balance. An object weighing 8200 N in air weighs 4740 N in water. Determine the volume and average density of the object. (The object is completely submerged in water.)
The thin plate depicted below is submerged in water with weight density 62.4 lb/ft³. What is the total force exerted on the plate? 4 ft v=4-x²1 4 ft 4 ft
For the vertical wall shown on the left, the oil thickness is assumed to be 0.2 m and its SG is 0.8. Assume the wall and gate width (into the paper) are 2 meters. Draw the pressure diagram. Assume the density of water is 1000 kg/m2 and g = 9.8 m/s2. Oil Determine а. Pressure at the interface between oil and water Water b. Pressure on the hinge С. Pressure at the base of the gate 2.1 m d. Amount of force acting on the gate Hinge е. Location of the force relative from the hinge 2-m-wide 0.8 m gate
A solid cylinder made of cast iron has the dimension r = 30cm and h = 2m. The cylinder is to be completely submerged in oil.Determine the force magnitude and direction required to achieve this. (density of cast iron = 7.3 g/cm3; density of oil = 790 kg/m3)
The manometer pictured has been filled with 2 different fluids and is open to the atmosphere on both sides. If fluid 1 has a density of 1g/cm3, the approximate density of fluid 2 is: Fluid 1 Fluid 2
A tank is filled with fluid under pressure and the pressure gauge fixed at the top indicates a pressure of 21 kPa. The curved surface of the top is quarter of a circular part of radius 2.6 m. calculate the magnitude (N) and direction (degree) of the resultant force on the curved surface. (p =950 kg/m³ for fluid) IB
A glass tube of internal diameter 3 mm is immersed in mercury. The angle of contact of mercury with glass can be taken as 130°. What will be the level of Hg in the tube relative to the free surface of the liquid outside the tube? Take surface tension of liquid = 0.48 N/m.
A tank is filled with fluid under pressure and the pressure gauge fixed at the top indicates a pressure of 21 kPa. The curved surface of the top is quarter of a circular part of radius 2.6 m. calculate the magnitude (N) and direction (degree) of the resultant force on the curved surface. (p =950 kg/m³ for fluid) B
A closed tank whose bottom is 18 inches in diameter is filled with three liquids: 4 inches of carbon tetrachloride (SG=1.59), 2 inches of water and 12 inches of syrup (SG=1.31). The air chamber in the tank is pressurized at 1296 psf. Apply the PANEL EQUATIONS to determine the magnitude, direction and location of the total hydrostatic force acting at the bottom of the tank.
A piece of irregularly shaped metal weighs 422 N in air. When the metal is completely submerged in water, it weighs 381 N. The volume of the metal is m³.