What is the ratio of total convective heat transfer rate to laminar convective heat transfer rate for the flow over 2 m length flat plate if 10 m/s air velocity is observed? For air: ν = 20x10-6 m2/s

What is the ratio of total convective heat transfer rate to laminar convective heat transfer rate for the flow over 2 m length flat plate if 10 m/s air velocity is observed? For air: ν = 20x10-6 m2/s

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.22P

See similar textbooks

Related questions

Q: Water at 90 °C enters a 10-cm-diameter and 400-m-long uninsulated pipe at a rate of 4.5 kg/s and…

A: Given that, Entering temperature of water, Ti=90 °C,Diameter of pipe, d=10 cm,Length of the pipe,…

Q: A 20 °C water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface…

Q: A coated sheet is being dried with hot air blowing in cross flow on the sheet surface. The surface…

A: Given data as per question The surface temperature of sheet = 90°C Air velocity = 0.3 m/s Air…

Q: In the laminar flow of air (Pr = 0.7) over a heated plate. if ö and S denote, respectively, the…

Q: e- Water at 12 °C is to be heated to 60 °C by passing it over a bundle of 3-m-long, 2-cm-diameter…

Q: 5. A 1 cm , 4 m long diameter resistance heater rod is to be used to heat water at 15°C is to 65°C…

A: Data given-

Q: Glycerin is being heated by flowing between two parallel 1-m-wide and 10-m-long plates with 12.5-mm…

A: Given: The width of the plate, w = 1 m The length of the plate, L = 10 m The spacing of plates, t =…

Q: Q5) Air at -10°C flows over a flat surface at 10°C with a free stream velocity of 80 m/s. The length…

A: given data air temperature = -10°C air speed = 80 m/s surface temperature = 10 °C length of plate =…

Q: Engine oil at 80°C flows over a flat surface at 40°C for cooling purpose, the flow velocity being 2…

A: Given Velocity, v = 2 m/s Distance, x = 0.4 m Properties at 80 + 40 /2 = 60oC Kinematic…

Q: 1. The mean Nusselt number for fully developed laminar flow in a circular tube under constant heat…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-…

Q: Air at 20 ◦ C flows inside a pipe 18-mm-ID having a uniform heat flux of 150 W/m 2 on the surface,…

A: Given that: q"=150 W/m2 d = 18 mm v = 1.0 m/s Pa = 2 bar T = 293 K ρ=PRT=2*105287*293=2.378 kg/m3

Q: The local heat transfer coefficient hy 5 x.75 for flow of water over a 2 m long and 0.5 m wide…

A: given data: local heat transfer coefficient; hx = 5x0.75 length of water; l = 2m width of water; b =…

Q: Choose the right answer 1. The mean Nusselt number for fully developed laminar flow in a circular…

Q: Water at 15ºC is to be heated to 65ºC by passing it over a bundle of 4-m-long 1-cm-diameter…

Q: Water from an industrial process flows through a long pipe of diameter 0.2m at a mass flow of 1.25…

Q: Air at atmospheric pressure and 25oC is heated in a tube with an ID of 25 mm. The tube wall is…

A: Solution: Given Data: Pi=1.013 barTi=25oCD=25 mmTw=200oCTo=120oCV.=10 Nm3/hr To find: Length of…

Q: Q6) Air at 30°C flows with a velocity of 6 m/s over a 2.5-mx8-m flat plate whose temperature is 120…

Q: Cold air at 5°C enters a l2-cm-diameter, 20-m-long isothermal pipe at a velocity of 2.5 m/s and…

A: Assumptions steady flow of air exist. Properties of air are taken at average temperature of inlet…

Q: Water at a temperature of 20 oC with a mass flow rate of 0.015 kg/s enters the pipe 2.5 cm in…

A: Dear student, we are suppose to solve only 3 sub parts. Please post other parts as a separate…

Q: For laminar flow over a hot flat plate, the local heat transfer coefficient decreases with distance…

A: Given question: For laminar flow over a hot flat plate, the local heat transfer coefficient…

Q: Air at 1 atm with a velocity of 4 m/s and a temperature of 50oC flows over a flat plate that is at a…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: Example 1: The components of an electronic system are located in a 1.5-m-long horizontal duct whose…

Q: Water at 1500 kg/h and 10°C enters a 10-mmdiameter smooth tube whose wall temperature is maintained…

A: Given data as per question Water flow rate = 1500 kg/h Temperature of water at entrance = 10°C…

Q: A flat plate 1.5 m wide and 2.0 m long whose surface is kept at 150 oC will be cooled by a current…

A: Laminar flow: Laminar flow is a type of fluid (gas or liquid) movement in which the fluid moves…

Q: Water at 45.0oC flows over a large plate at a velocity of 30.0 cm/s. The plate is 1.0 m long (in the…

Q: Air with a pressure of 1 atm and a temperature of 285 K flows in a duct rectangular shape with a…

A: Given, Pressure, P=1atmTemperature, T=285KMass flow rate, m=0.1kg/sDuct size=75mm×150mmLength of…

Q: For seaworthiness trial of a new ocean-going vessel design, the total convective heat transfer rate…

Q: Consider atmospheric air at 25?C and a velocity of 25 m/s flowing over both surfaces of a 1-m-long…

Q: e- Water at 12 °C is to be heated to 60 °C by passing it over a bundle of 3-m-long, 2-cm-diameter…

Q: A flat plate of width 1 m and length 0.22 m is maintained at a temperature of 32°C. Ambient fluid at…

Q: Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220oC flows in…

Q: For flow over a flat plate of length L, the local heat transfer coefficient hx is known to vary as…

Q: Choose the right answer 1. The mean Nusselt number for fully developed laminar flow in a circular…

Q: Air stream at 1 atm flows with a velocity of 2 m/s, in parallel over a 3 m long square flat plate,…

A: Given: The air stream pressure, P = 1 atm The velocity of air stream, v = 2 m/s The length of plate,…

Q: Write your answer in 4 decimal places. DO NOT round off intermediate values. Water at a mean…

Q: xhaust gases at 1 atm and 300°C are used to preheat water in an industrial facility by passing them…

Q: Q3/Air at 0.5 atm pressure and 27 C flows across a 34-cm-square plate at a velocity of 20 m/s. The…

Q: At an average temperature of 100°C, hot air flows through a 2.5 m long tube with an inside diameter…

A: Given Data The average temperature of hot air is; T∞=100°C The temperature of the tube is; Tt=20°C…

Q: Nitrogen at 1 atm and 100 °C enters into an equilateral triangular cross section duct of each side…

Q: Evaluate the convection heat transfer coefficient for the flow of (a) air and (b) water at a…

Q: When the free-flow velocity on the plate is 10 m/s, (a) when water with a kinematic coefficient of…

A: Given data: flow velocity (V) = 10 m/s Reynolds number (Re) = 500,000 To find: a. when kinematic…

Q: As shown in the figure, electrical heaters operating in the V=220 V are placed on the lower surface…

Question

What is the ratio of total convective heat transfer rate to laminar convective heat transfer rate for the flow over 2 m length flat plate if 10 m/s air velocity is observed?

For air: ν = 20x10-6 m2/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?
Air at 20°C, 1 atm flows with a velocity of 4.5 m/s over a flat plate having a sharp leading edge. The plate surface isothermal at 60°C. (a), determine the following parameters at a distance of 1.89m. i)Local convective heat transfer coefficient (ii)Average convective heat transfer coefficient (iii)The heat transfer rate from both sides per unit width of the plate
For laminar flow over a hot flat plate, the local heat transfer coefficient decreases with distance because (select all that are correct) The thickness of the heated region near the plate is increasing. The velocities near the plate are decreasing. The fluid temperatures near the plate are increasing.
For flow over a flat plate of length L, the local heat transfer coefficient hx is -1/2 known to vary as x2, where x is the distance from the leading edge of the plate. What is the ratio of the average Nusselt number for the entire plate ( Nu1) to the local Nusselt number at x = L( Nu,)?
Air with free stream temperature of 10 C is flowing over a flat plate (1.5m long and Im wide). The air is flowing along 1.5m side of the plate. The plate is maintained at 90 C. Find the velocity of air required to have a rate of heat dissipation as 3.75 kW. Use the correlations: Nu =0.664Res Pro3 for laminar flow Nu, = (0.037R *-871)Pr for turbulent flow Take the properties p = 1.0877 kg/m u=2.029x10 m/s, k=0.028 W/mK, C,-1.007KJ/kg.K and Pr=0.703 %3D
Air at 20 ◦ C flows inside a pipe 18-mm-ID having a uniform heat flux of 150 W/m 2 on the surface, the average flow velocity at entry being 1.0 m/s. The air pressure is 2 bar. Determine the value of convection coefficient. If the pipe is 2.5 m long, determine the air exit temperature and the wall temperature at the exit. Assume fully developed hydrodynamic boundary layer.
A 4m x 4m flat piale maintained at a constant temperature of NOC is subjected to parallel flow of nit at I am. 20 ', and 10 m's. The total drag force acting on the upper surface of the plate is measured to be 2.4N Determine the average convection hear transfer coefficient, and the rate of heat transfer between the upper surface of the plate and the air. The properties of air at 20 ° C and 1 atm from tables, are
Air at 400C flows with a velocity of 7 m/s over a 5m long and 4m wide surface of a flat plate whose surface temperature is 800C. Find the rate of heat transfer from the laminar flow region of the surface. (For air at 400C , V = 1.702 × 10-5 , pr = 0.7255, K = 0.02662 w/m . K
The air at 1 ATM and 35⁰c flow through a cylinder 5 cm in diameter,at Velocity 50 cm/s. The surface temperature of the cylinder is guarded at 150⁰c *)Calculating heat loss per cylinder unit
Air at 400C flows with a velocity of 7 m/s over a 5m long and 4m wilde surface of a flat plate whose surface temperature is 800C. Find the rate of heat transfer from the laminar flow region of the surface. (For air at 400C , V = 1.702 × 10-5 , pr = 0.7255, K = 0.02662 w/m . K).
Air at a velocity of 4 m/s and temperature of 30°C flows over a 2 m long rod with a diameter of 5 cm that is maintained at a uniform temperature of 90°C. Find the convective heat flux to the rod. -1786:34/m²